基于单片机的智能晾衣架控制系统的设计与实现外文文献原稿和译文

1、燕京理工学院毕业设计（论文）外文文献原稿和译文外文文献原稿和译文原稿The Description of AT89S511 General DescriptionThe AT89S51 is a low-power, high-performance CMOS 8-bit microcontroller with 4K bytes of In-System Programmable Flash memory. The device is manufactured using Atmels high-density nonvolatile memory technology and is compatible with the industry-standard 80C51 instruction set and pinout. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By com

2、bining a versatile 8-bit CPU with In-System Programmable Flash on a monolithic chip, the Atmel AT89S51 is a powerful microcontroller which provides a highly-flexible and cost-effective solution to many embedded control applications.The AT89S51 provides the following standard features: 4K bytes of Flash, 128 bytes of RAM, 32 I/O lines, Watchdog timer, two data pointers, two 16-bit timer/counters, a five-vector two-level interrupt architecture, a full duplex serial port, on-chip oscillator, and cl

3、ock circuitry. In addition, the AT89S51 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port, and interrupt system to continue functioning. The Power-down mode saves the RAM contents but freezes the oscillator, disabling all other chip functions until the next external interrupt or hardware reset.2 PortsPort 0 is an 8-bit open drain bi-directional

4、 I/O port. As an output port, each pin can sink eight TTL inputs. When 1s are written to port 0 pins, the pins can be used as high-impedance inputs. Port 0 can also be configured to be the multiplexed low-order address/data bus during accesses to external program and data memory. In this mode, P0 has internal pull-ups. Port 0 also receives the code bytes during Flash programming and outputs the code bytes during program verification. External pull-ups are required during program verification.Por

5、t 1 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 1 output buffers can sink/source four TTL inputs. When 1s are written to Port 1 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 1 pins that are externally being pulled low will source current (IIL) because of the internal pull-ups. Port 1 also receives the low-order address bytes during Flash programming and verification.Port PinAlternate FunctionsP1.5MOSI (used for In-System P

6、rogramming)P1.6MOSO (used for In-System Programming)P1.7 SCK(used for In-System Programming)Port 2 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 2 output buffers can sink/source four TTL inputs. When 1s are written to Port 2 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (IIL) because of the internal pull-ups.Port 2 emits the high-order address byte during fetche

7、s from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX DPTR). In this application, Port 2 uses strong internal pull-ups when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOVX RI), Port 2 emits the contents of the P2 Special Function Register. Port 2 also receives the high-order address bits and some control signals during Flash programming and verification.Port 3 is an 8-bit bi-directional I/O port with interna

8、l pull-ups. The Port 3 output buffers can sink/source four TTL inputs. When 1s are written to Port 3 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (IIL) because of the pull-ups. Port 3 receives some control signals for Flash programming and verification. Port 3 also serves the functions of various special features of the AT89S51, as shown in the following table.Port PinAlternate Funct

9、ionsP3.0RXD(serial input port)P3.1TXD(serial output port)P3.2INT0(external interrupt 0)P3.3INT1(external interrupt 1)P3.4T0(timer 0 external input)P3.5T1(timer 1 external input)P3.6WR(external data memory write strobe)P3.7RD(external data memory read strobe)3 Special Function RegistersA map of the on-chip memory area called the Special Function Register (SFR) space is shown in Table 3-1. Table 3-1. AT89S51 SFR Map and Reset Values0F8H 0FFH 0F0H B 00000000 0F7H 0E8H 0EFH 0E0H ACC 00000000 0E7H 0D8H 0DFH 0D0H PSW 00000000 0D7H 0C8H 0CFH 0C0H 0C7H 0B8H IP XX000000 0BFH 0B0H P3 11111111 0B7H 0A8H IE 0X000000 0AFH 0A0H P2 11111111 AUXR1 XXXXX

《基于单片机的智能晾衣架控制系统的设计与实现外文文献原稿和译文》由会员M****1分享，可在线阅读，更多相关《基于单片机的智能晾衣架控制系统的设计与实现外文文献原稿和译文》请在金锄头文库上搜索。