工业盘式制动器
9页1、litLA.fi制动器销售13782761872www. zhidongqichang. com制动器销售13782761872盘式制动器www zhidongqichaIndustrial disc brake device5SE-450SE-4SE-3SE5SH-450SH-4SH-3SF5SP-450SP-4SP-3SP失效保护制动器Useless protection brake安装、调整及维修手册Installment , adjustment and maintenance manual焦作市盘式制动器有限公司Jiaozuo Panshi brake co.,ltd1. 制动器的安装 brake install 操作者站在制动盘相对于制动器的对面。Operator who stand in brake disc is opposite to brake device1.1 拧紧手动松闸螺钉 4(螺钉规格见表 1)松开锁紧的制动器并移动杠杆和摩擦 衬垫,观察和调整两制动摩擦衬垫间的间隙。注意:手动松闸操作时,切勿引起电磁铁的运动。manually tightening scr
2、ew 4 (screw specifications are seen in Table 1) loosen the locking brake and move the level and friction pad , observation and adjustment the gap between the brake and friction pad .attention: When operate the manual loose gate , make sure not to move the electro-magnet 1.2(向上)顺时针旋转棘轮 5 的手轮1 大约四分之一转(微调)(upward) clockwise rotate handwheels 1 ofnotch wheel 5 about 1/4 revolutions (trimming)1.3 (向下)逆时针旋转螺母2 (用一个04的销子)以便退回回推杆3,这将增加衬垫6 之间的间隙,继续该操作,直到两摩擦衬垫间隙超过制动盘的厚度。 (downward) anticlockwise rotate nu
3、t 2 (with a 04 pin) in order to return the throwout lever 3, this will increasethe gapsbetween the pad 6, continues this operation, until the gap between two friction padssurpasses brake discs thickness. 1.4将制动瓦置于其支撑物上,在制动衬垫之间插入制动盘,安装底座连接螺栓(螺栓规格见表 1)Brake tile is placedon its strutting ,insertbrake discbetweenthe brake pad, installs the foundation connecting bolt (bolt specification is seen inTable 1 ) 1.5 检查:A) 制动盘端面跳动,最大值 0.2mmB) 制动盘垫块相对于底座度: 4%C) 制动盘相对于底座的中心距(偏差) 2.5mm注意油漆时不要盖住显示棘爪运动方向的板1.5 i
4、nspections:A) Brake disc ending beat, maximum value 0.2mmB) The brake disc cushion compared with the foundation: 4%C) compared with the brake disc ,the center of the base (bias) 2.5mmAttentionwhen paint do not cover the board that demonstratethe movement direction of pawl2退距的调整 draws back adjustment操作者站在制动盘相对于制动器的对面Operator who stand in brake disc is opposite to brake device2.1 拧紧手动松闸螺钉 4(螺钉规格见表 1)松开锁紧的制动盘,并移动杠杆和 摩擦衬垫的间隙。注意:手动松闸操作时,切勿引起电磁铁的运动。manually tightening screw 4 (screw specifications are
《工业盘式制动器》由会员cl****1分享,可在线阅读,更多相关《工业盘式制动器》请在金锄头文库上搜索。
2023电工个人年终工作总结范本(8篇).doc
13年名师解读:对备战中考物理的建议
三基考试题库与答案
疾病预防演讲稿
2023幼儿园安全工作个人总结(3篇).doc
《电脑住宅》教学设计
新版谈高校图书馆的人性化服务汇编
2022美容化妆人员考试(全能考点剖析)名师点拨卷含答案附答案44
东北农业大学21秋《物权法》平时作业二参考答案42
4分钟祠堂落成庆典致辞稿5篇
儿科门诊护理工作计划模板
幼儿园小班老师个人工作总结
04 保管工具登记表QR630204
如何开展我市农村信息网络建设
2019年如法网学法答案
五年级下册品德与社会教学计划和进度
学生成长档案
小区安保年终总结(7篇).doc
晶闸管技术术语
管道气压通球方案
2023-04-07 24页
2023-03-22 27页
2024-01-09 42页
2023-07-04 17页
2023-03-03 3页
2023-12-31 32页
2024-01-09 6页
2023-08-27 3页
2022-11-27 18页
2022-09-26 17页