过度专题方案专业资料.docx

IPV6/IPV4过度机制1.双合同栈口172.16.10.2/24 ^=H-'PC-PT、PC2 \XFdO/1-一# 28112SLLPC-PT/ Reuter 0Route rlPCS10.10.10.2/24172.16.8.2/24-—；■'PCI::10:2/112图1双合同栈拓扑表1-1设备IP地址配备设备 接口IPv4地址IPv6地址Router0 F0/0172.16.8.1/24::10:1/112F0/1172.16.10.1/24::1:2/112S2/0192.168.10.1/24::12:1/112Router1 F0/010.10.10.1/24S2/0192.168.10.2/24::12:2/112重要配备Routerl 配备：(1)配备接口地址Routerl(config)# ipv6 unicast-routingRouter1(config)# int f0/0Router1(config-if)# ipv6 address ::10:1/112Router1(config-if)# ip address 172.16.8.1 255.255.255.0Router1(config-if)# no shutdown 相应日勺接口做同样日勺配备即可。

2)配备路由合同RIPngRouterl(config)# router ripRouterl(config-router)# version 2Router1(config-router)#network 172.16.8.0Router1(config-router)#network 192.168.10.0Router1(config)# ipv6 router rip r1Router1(config-if)# int f0/0Router1(config-if)# ipv6 rip r1 enable在相应ipv6端口应用RIPng即可Router2配备类似连通性测试PC1 ping PC3ping成功，证明PC1与PC3可以通过IPV4进行通信PC1 ping PC2Pinging ZQ11:= 1 with 3卫 byves q£ a:Reply ZEQm 2011 = =1:1: bytes=3 2 tlme=12 5zi^ TTIj=12 7Reply ZEQm 2011izl:l: k>ytes=3 2 time=47in3 TIIj=L2 7Reply ^rroiri 2 011 z z 1: 1 : k>ytes=3 2 1;±111£=^2]113 TTZj=12 7Reply ZEom 2 011 : : 1: 1: bytes=32 tim£=G'3in3 inj=L2 7Ping statzls t i cs for 2 011 z z L : 1:Packets: Sent = 4 r Recelve-d = 4F Lost = 0 (01 loss) pApprajLlmat;e roxind. trip txines in milli.-seccn-dszHinimuni = 47ms p Majtinimn = 12 Sms F Average = 7 4m=iPing成功，证明PC1与PC2可以通过IPV6进行通信。

2.手工隧道f(l/iR3 200t:250:ffff=6=tl/5&图2.手工隧道拓扑重要配备Router4重要配备如下：R4(config)# ipv6 unicast-routingR4(config)#int f0/0R4(config-if)#no shutdownR4(config-if)#ip address 192.168.1.1 255.255.255.0R4(config-if)#int f0/1R4(config-if)#no shutdownR4(config-if)#ipv6 address :251:ffff:5::1/64R4(conifg)# router ripR4(conifg-router)# network 192.168.1.0R4(conifg-router)# version 2R4(conifg-router)# no auR4(conifg)#int tunnel 0R4(config-if)#ipv6 address :1:5:1::1/64R4(config-if)#tunnel source 192.168.1.1R4(config-if)#tunnel destination 192.168.2.2R4(config-if)#tunnel mode ipv6ipR4(conifg)#ipv6 route :250:FFFF:5::/64 tunnel 0Router3重要配备如下：R3(config)# ipv6 unicast-routingR3(config)#int f0/0R3(config-if)#no shutdownR3(config-if)#ip address 192.168.1.2 255.255.255.0R3(config-if)#int f0/1R3(config-if)#no shutdownR3(config-if)#ipv6 address :250:ffff:5::1/64R3(conifg)# router ripR3(conifg-router)# network 192.168.2.0R3(conifg-router)# version 2R3(conifg-router)# no auR3(conifg)#int tunnel 0R3(config-if)#ipv6 address :1:5:2::1/64。