震雄注塑机规格.doc

说明DESCRIPTIONSUNITJM55MKⅢ-C射胶部分INJECTION UNIT　　射胶量（硬胶）Shot Weight (PS)oz.2.4　　gm.69射胶容量Swept Volumecm380螺杆直径Screw Diametermm.28射胶压力Injection Pressurekgf./cm21715螺杆行程Screw Strokemm.130螺杆转速Screw Speed RangeR.P.M0-140熔胶能力Plasticizing Capacitykg/hr.40料斗容量Hopper Capacityl.31射嘴行程Nozzle Travel Strokem.m.220螺杆长度直径比Screw L/D Ratio　19锁模部分CLAMPING UNIT　　锁模力Clamping ForceMp.55开模行程Opening Strokemm.220连接柱内距（水平×垂直）Space Between Tie Bars (H×V)mm.×mm.310×310容模量（最薄-最厚）Mould Thickness (Min-Max)mm.80-320模板最大距离Maximum Daylightmm.540油压顶针推力Hydraulic Ejector ForceMp.2.2油压顶针行程Hydraulic Ejector Strokemm.75定位法兰直径Mould Register Hole (H7)mm.100动力/电热POWER/HEATING 　　油泵马力Pump MotorKW.(HP)7.5(10)电热量Heating CapacityKW.4.8系统压力System Pressurekfg./cm2145温度控制区No. of Temp. Control Zones　2+1其它OTHERS　　循环时间Dry Cycle Timesec.1.6占地面积Floor Spacem.×m.3×1.2装箱尺寸Shipping Dimensionm.×m.×m.3.5×1×1.6油缸容量Oil Tank Capacityl.150机重Machine Weight (Dry)ton.2.4说明DESCRIPTIONSUNITJM88MKⅢ-C射胶部分INJECTION UNIT　　射胶量（硬胶）Shot Weight (PS)oz.4.5　　gm.128射胶容量Swept Volumecm3142螺杆直径Screw Diametermm.36射胶压力Injection Pressurekgf./cm21500螺杆行程Screw Strokemm.140螺杆转速Screw Speed RangeR.P.M10-152熔胶能力Plasticizing Capacitykg/hr.65料斗容量Hopper Capacityl.31射嘴行程Nozzle Travel Strokem.m.219螺杆长度直径比Screw L/D Ratio　19锁模部分CLAMPING UNIT　　锁模力Clamping ForceMp.88开模行程Opening Strokemm.270连接柱内距（水平×垂直）Space Between Tie Bars (H×V)mm.×mm.360×360容模量（最薄-最厚）Mould Thickness (Min-Max)mm.127-350模板最大距离Maximum Daylightmm.620油压顶针推力Hydraulic Ejector ForceMp.3油压顶针行程Hydraulic Ejector Strokemm.75定位法兰直径Mould Register Hole (H7)mm.100动力/电热POWER/HEATING 　　油泵马力Pump MotorKW.(HP)7.5(10)电热量Heating CapacityKW.5.6系统压力System Pressurekfg./cm2145温度控制区No. of Temp. Control Zones　2+1其它OTHERS　　循环时间Dry Cycle Timesec.1.2占地面积Floor Spacem.×m.3.8×1.3装箱尺寸Shipping Dimensionm.×m.×m.3.9×1.2×1.7油缸容量Oil Tank Capacityl.150机重Machine Weight (Dry)ton.3.4说明DESCRIPTIONSUNITJM128MKⅢ-C射胶部分INJECTION UNIT　　射胶量（硬胶）Shot Weight (PS)oz.9　　gm.255射胶容量Swept Volumecm3283螺杆直径Screw Diametermm.46射胶压力Injection Pressurekgf./cm21687螺杆行程Screw Strokemm.170螺杆转速Screw Speed RangeR.P.M10-200熔胶能力Plasticizing Capacitykg/hr.100料斗容量Hopper Capacityl.45射嘴行程Nozzle Travel Strokem.m.280螺杆长度直径比Screw L/D Ratio　20锁模部分CLAMPING UNIT　　锁模力Clamping ForceMp.128开模行程Opening Strokemm.305连接柱内距（水平×垂直）Space Between Tie Bars (H×V)mm.×mm.410×360容模量（最薄-最厚）Mould Thickness (Min-Max)mm.175-400模板最大距离Maximum Daylightmm.705油压顶针推力Hydraulic Ejector ForceMp.3.4油压顶针行程Hydraulic Ejector Strokemm.100定位法兰直径Mould Register Hole (H7)mm.100动力/电热POWER/HEATING 　　油泵马力Pump MotorKW.(HP)15(20)电热量Heating CapacityKW.13.4系统压力System Pressurekfg./cm2175温度控制区No. of Temp. Control Zones　3+1其它OTHERS　　循环时间Dry Cycle Timesec.1.3占地面积Floor Spacem.×m.4.46×0.98装箱尺寸Shipping Dimensionm.×m.×m.4.7×1.1×1.6油缸容量Oil Tank Capacityl.300机重Machine Weight (Dry)ton.3.8说明DESCRIPTIONSUNITJM168MKⅢ-C射胶部分INJECTION UNIT　　射胶量（硬胶）Shot Weight (PS)oz.14　　gm.396射胶容量Swept Volumecm3435螺杆直径Screw Diametermm.52射胶压力Injection Pressurekgf./cm21437螺杆行程Screw Strokemm.205螺杆转速Screw Speed RangeR.P.M10-150熔胶能力Plasticizing Capacitykg/hr.110料斗容量Hopper Capacityl.70射嘴行程Nozzle Travel Strokem.m.300螺杆长度直径比Screw L/D Ratio　20锁模部分CLAMPING UNIT　　锁模力Clamping ForceMp.168开模行程Opening Strokemm.350连接柱内距（水平×垂直）Space Between Tie Bars (H×V)mm.×mm.460×410容模量（最薄-最厚）Mould Thickness (Min-Max)mm.220-450模板最大距离Maximum Daylightmm.800油压顶针推力Hydraulic Ejector ForceMp.4.5油压顶针行程Hydraulic Ejector Strokemm.100定位法兰直径Mould Register Hole (H7)mm.120动力/电热POWER/HEATING 　　油泵马力Pump MotorKW.(HP)18.75(25)电热量Heating CapacityKW.16系统压力System Pressurekfg./cm2145温度控制区No. of Temp. Control Zones　3+1其它OTHERS　　循环时间Dry Cycle Timesec.1.6占地面积Floor Spacem.×m.4.95×1.05装箱尺寸Shipping Dimensionm.×m.×m.5×1.2×1.6油缸容量Oil Tank Capacityl.400机重Machine Weight (Dry)ton.4.7说明DESCRIPTIONSUNITJM218MKⅢ-C射胶部分INJECTION UNIT　　射胶量（硬胶）Shot Weight (PS)oz.21　　gm.595。