组件过程及最终检验标准.docx

一、过程检验标准一、过程检验标准1.1.芯片检验标准芯片检验标准 芯片级别芯片级别检检 验验 标标 准准A 级转换效率≥≥14%(单晶）或 13.5%（多晶）；正面无挂浆；无裂纹； 细棚线断线≤≤0.5mm 不超过 3 条且不连续分布；缺角和崩口 ≤0.5mm2 不超过 3 个；层压后无明显色差；无逆电流；2.2.玻璃检验标准玻璃检验标准玻璃级别玻璃级别检检 验验 标标 准准A 级透光率≥≥95%，气泡线度≤≤2mm 不超过 3 个，极浅划伤 L≤≤10mm 不超过 3 条；崩边向中间延伸≤≤1mm 不超过 3 个；平整度≤≤5%3.3.铝合金检验标准铝合金检验标准铝合金级别铝合金级别检检 验验 标标 准准A 级铝合金标号 6063T5；表面氧化均匀，氧化膜层厚度≥≥10um； 表面无划伤、无鼓包；两端高、宽、厚等线度尺寸相差 ≤≤0.3mm4.4.涂锡带检验标准涂锡带检验标准尺寸公差≤≤±0.01mm，涂锡层均匀，易于焊接，抗拉强度好，不易断裂。

5.5.接线盒检验标准接线盒检验标准密封、防水，能与硅橡胶牢固粘合，耐老化，绝缘，具有旁路二极管，二 极管具有足够的反向耐压和较低正向漏电流，二极管具有高低温的耐温性，整 个线路具有较低的电阻，盒体具有足够的散热空间，插头具有好的耐疲劳性二、最终检验标准二、最终检验标准技术技术 级别级别功率功率 范围范围外形外形 尺寸尺寸正正 面面 外外 观观边框外观边框外观背面外观背面外观A 级≤≤± 3%公差 ≤1.0 mm 两端 尺寸 相差 ≤0.5 mm芯片无挂浆，边缘裂纹≤5mm 不超过 1 条，细栅线断线 ≤0.5mm 不超过 3 条且不连续 分布，缺角和崩口≤0.5mm2不 超过 3 个，表面无明显色差； 玻璃极浅划伤 L≤10mm 不超过 3 条；组件气泡≤3mm2不超过 3 个；芯片间距离不小于 1mm，芯片与边框间距离不小 于 8mm表面氧化均 匀，表面无 划伤、无鼓 包；两端线 度尺寸相差 ≤≤0.3mmTPT 无皱 痕，表面干 净，拱起点 高度 ≤≤0.2mm;硅 胶均匀；接 线盒粘接牢 固，表面干 净三、相应规格电气性能参数125*125 MONO 180WpSpecifications Data Max. Power180WpCell TypeMono-Crystalline Silicon Sorlar CellNo.Of Cells 72 seriesMax.System Voltage1000VDCPower Tolerance±3% Surface Maximum Load Capacity60m/s(200kg/sq.m)Weight15.5kgDimemsions1580×808×35mm Electrical Characeteristic Open Circuil Voltage(V) 44.4Short Circuil Currenl(A)5.40Max.Power Voltage(V)35.6Max.power Current(A)5.05Temperature Coefficienls of Isc(%)+0.017%℃ Temperature Coefficienls of Voc(%)-0.34%℃ Temperature Coefficienls of Pm(%)-0.48%℃ Operating Temperralure-40 to + 85℃Conditions:(STC):Irradiance:1000W/m2, spectral distribution AM1.5, Cell temperature:25℃℃ Features and Benefits High efficicncy solar cells Nominal 24V DC for standard outputCells are Iaminated with EVA, TPT and tempered glass ensuring long life and the most stringent safety requirements for high- voltage operation. Anodized aluminum frame with convenience mounting slots Withstand hing wind pressure and snow load Outstanding low-light performance Preeminent aesthetic appearance Easy installationOutput power tolerance of ±3%25 year limited warranty on power output, 2 year limited warranty on materials and workmanship156*156 100WpSpecifications Data Max. Power100WpCell TypeMono-Crystalline Silicon Sorlar CellNo.Of Cells 36 seriesMax.System Voltage1000VDCPower Tolerance±3% Surface Maximum Load Capacity60m/s(200kg/sq.m)Weight10.0kgDimemsions1476×670×35mm Electrical Characeteristic Open Circuil Voltage(V) 21.4Short Circuil Currenl(A)5.40Max.Power Voltage(V)17.6Max.power Current(A)6.40Temperature Coefficienls of Isc(%)+0.017%℃ Temperature Coefficienls of Voc(%)-0.34%℃Temperature Coefficienls of Pm(%)-0.48%℃ Operating Temperralure-40 to + 85℃Conditions:(STC):Irradiance:1000W/m2, spectral distribution AM1.5, Cell temperature:25℃℃ Features and Benefits High efficicncy solar cells Nominal 12V DC for standard outputCells are Iaminated with EVA, TPT and tempered glass ensuring long life and the most stringent safety requirements for high- voltage operation. Anodized aluminum frame with convenience mounting slots Withstand hing wind pressure and snow load Outstanding low-light performance Preeminent aesthetic appearance Easy installationOutput power tolerance of ±3%25 year limited warranty on power output, 2 year limited warranty on materials and workmanship。