CNC数控系统通讯参数设置.doc

1 / 15CNC 数控系统通讯参数设置数控系统通讯参数设置AllenBradley（美国：AB）AllenBradley 8600Parameter Value Comments Baud Rate 2400 Parity E Databits 7 Stop Bits 2 Acramatic（美国：辛辛那提（美国：辛辛那提·米拉克龙）米拉克龙）Acramatic 850 (SX) Parameter Value Comments Baud Rate 2400 Also set these values in the DNC software Parity N Databits 8 Stop Bits 1 Drip Feed ? We do not believe drip feed is possible with this controller See bottom of this page for Cable diagrams Anilam（美国：艾科瑞）（美国：艾科瑞）Anilam Crusader Parameter Value Comments Group 1 AUX 2767 7 Data bits Group 2 AUX 2772 Even Parity Group 3 AUX 2784 Baud Rate 1200 Group 4 AUX 2790 No Flow Control Group 5 AUX 2700 Send from Crusader to PC Group 6 AUX 2701 Receive data in Crusdare (From PC) Bosch（美国：博世（美国：博世··力士乐）力士乐）Bosch CC220 and CC320 2 / 15Parameter Value Comments Device Port (V240,1) DCR 9600 Baud Rate Status SW Control DFS RECOGNISE WITH LEADER WITH TRAILER Time Out 10 SEC Haas（美国：哈斯）（美国：哈斯）HaasParameter Value Comments 11 9600 12 Even 13 1 14 Xon/Xoff 37 7 24 None 25 CR,LF 41 On 50 Xon/Xoff 54 9600 69 Off 70 On BossBridgeport Boss Parameter Value Comments Baud Rate 4800 Parity Even Databits 7 Stop Bits 1 USE DNC Port B See Cable diagrams below DeltaDynaPath（美国：（美国： ））Delta Dynapath Parameter Value Comments Baud Rate Any Suggest 2400 but not higher than 9600) 3 / 15Databits 7 Parity Even Stop bits 1 FadalCNC（美国：法道）（美国：法道）Fadal 88Parameter Value Comments Baud Rate 9600 Suggest 2400 but not higher than 9600) Databits 7 Parity Even Stop bits 1 Fanuc（日本：发那科）（日本：发那科）Fanuc i（（M/T））Parameter Value Comments 0000 0000 0010 0020 0 0100 0010 1000 0101 1000 1001 0102 0 0103 11 9 = 2400，10 = 4800，11 = 9600* (recommended)01381000 0000TV Check 0 0 = TV Check OFF (1= TV Check ON - Never enable TV Check) Punch Code 1 1 = ISO (0=EIA Never use EIA) I/O Channel 0 PWE1Drip Feed ? Select Auto (DNC) mode on the control - Press Cycle Start. 选择自动（DNC）控制状态，按（循环启动） 。

Then go to the computer, prepare the program and click 'Send'. When data begins to flow the machine will start moving. 然后去电脑，准备程序，点击“发送” ，当数据开始传送时，机床就会开始移动Fanuc 0（（M/T））Parameter Value Comments 0002 1000 0001 00380100 00000552 11 9 = 2400，10 = 4800，11 = 9600* (recommended)TV On/Off 0 0 = TV Check OFF (1= TV Check ON - Never enable TV Check) ISO 1 1 = ISO (0=EIA Never use EIA) 4 / 15I/O 0 PWE 1TAPEF 0Drip Feed ? To drip feed enable para G127.5 使 G127.5 DNC 操作信号动作Select Auto (DNC) mode on the control - Press Cycle Start. 选择自动（DNC）控制状态，按（循环启动） 。

Then go to the computer, prepare the program and click 'Send'. When data begins to flow the machine will start moving. 然后去电脑，准备程序，点击“发送” ，当数据开始传送时，机床就会开始移动Fanuc 3（（M/T））Parameter Value Comments 0005 0000 0001 0068 10 9 = 2400，10 = 4800* (recommended)，11 = 9600TV On/Off 0 0 = TV Check OFF (1= TV Check ON - Never enable TV Check) ISO 1 1 = ISO (0=EIA Never use EIA) I/O 0 Fanuc 6,9（（M/T）） ,0PParameter Value Comments 340 2 341 2 311 0011 1010 Baud rate - see table below for valid options. 0011 1000 = 2400 0011 1001 = 4800 0011 1010 = 9600 * (recommended)TV Check 0 0 = TV Check OFF (1= TV Check ON - Never enable TV Check) Punch Code 1 1 = ISO (0=EIA Never use EIA) Input Unit 0 Input Device 1 1 Input Device 2 1 Fanuc 10,11,12,15 (M/T) Parameter Value Comments 0000****1010 0011******000020 10021 12201******005 / 155001 1 5002 2 5003 3 5110 4 5111 2 5112 10 * Baud rate - see table below for valid options. 5120 4 5121 2 5122 10 * Baud rate - see table below for valid options. 5130 4 5131 2 5132 10 * Baud rate - see table below for valid options. 9 = 2400 10 = 4800 * (recommended)11 = 9600 TV Check 0 0 = TV Check OFF (1= TV Check ON - Never enable TV Check) ISO 0 0 = ISO (1=EIA Never use EIA) Input Device 1 Output Device 1 Drip Feed ? Select Tape mode on the control - Press Cycle Start. 选择 TAPE（磁带）控制状态，按（循环启动） 。

Then go to the computer, prepare the program and click 'Send'. When data begins to flow the machine will start moving. 然后去电脑，准备程序，点击“发送” ，当数据开始传送时，机床就会开始移动Note: Not all fanuc of this type can drip feed - must be enabled in the control. Fanuc 16,18,21 (M/T) Parameter Value Comments 0000 0000 0010 0020 0 0100 0010 1000 0101 1000 1001 0102 0 0103 10 9 = 2400，10 = 4800* (recommended)，11 = 9600TV Check 0 0 = TV Check OFF (1= TV Check ON - Never enable TV Check) Punch Code 1 1 = ISO (0=EIA Never use EIA) I/O Channel 0 Tape Format 0 Drip Feed ? Select TAPE mode on the control - Press Cycle Start. 选择 TAPE（磁带）控制状态，按（循环启动） 。

6 / 15Then go to the computer, prepare the program and click 'Send'. When data begins to flow the machine will start moving. 然后去电脑，准备程序，点击“发送” ，当数据开始传送时，机床就会开始移动Mazak（日本：马扎克）（日本：马扎克）Mazak M Plus / T Plus Paramete r Value Comments User Parameter #5 G1 1 = Baud Rate 9600 G2 3 = 2 Stop Bits G3 0 = Even Parity G5 3 = 8 Data Bits (Set DNC to software to 7 Databits) G6 1 G10 3 Use xOn/xOff flow control (DC1 and DC3) G12 0 。