KAA31474AAB_STM_NGSOK2门机资料全.doc

1 / 43Copyright 2012, OTIS Elevator Co. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of OTIS.Table of Contents1Introduction41.1Power On51.2Key Function Description52Software Overview72.1Local and Remote Service tool7Local SVT connection7Remote SVT connection72.2Menu Overview8Monitoring Functions 9Test Functions 9Setup 9Run 9Engineering 102.3Key-Function Overview102.4Access restriction for SVT Menu10Require SVC mode to access menu12Remote SVT inaccessible Menu123Function Menus143.1Monitoring Functions 14Status 15Input 17Output 19Runs: Run Time display 20Part: Display Software Version 20SysConfig 21Statistics 233.2TEST 24Event log 24History log 24Clear log 263.3Setup 27Inst: Installation 27CONFIGOPERATOR 27LEARN-RUN 29MASS: MOVING MASS INPUT 32DoorTim: Adjust Door Time 33Def.: Set Default 35NGSOK2Service Tool Users GuideAuthorization Date :2012. 07. 20Running on PCB:KAA26800ACA or laterSoftware Version:KAA31474AABDocument Revision:DateAuthorComment2011-03-14Hansoo ShimOriginal Document2012-07-20Hansoo ShimUpdated for KAA31474AAB.2 / 43InfChk: Interface check 37System Reset 38Parameters 39PROF1: PROFILE 1 PARAMETER SETUP 39PROF2: PROFILE 2 PARAMETER SETUP 40SYSTM: SYSTEM PARAMETER SETUP 40CNTRL: CONTROL PARAMETER SETUP 40SELECT: PROFILE SELECT 40PROF3: PROFILE 3 PARAMETER SETUP 41PROF4: PROFILE 4 PARAMETER SETUP 41FIRPRF: FIREMAN SVC PHASE 2 PROFILE PARAMETER SETUP 413.4Run 42Single: Single Door run 42Cont.: Cycle door run 43Off 433.5Engineering Menu44BusV&C: Bus voltagedisplay 44IDQV: Inverter current and voltage display 44DoorTime: Door Time Display45KE: Kinetic Energy 464Parameter Description474.1Profile 1 Parameters47Open parameters47Close parameters48Reopen parameters50Control Gain parameter504.2Profile 2 Parameters514.3Profile 3 Parameters514.4Profile 4 Parameters514.5Fireman SVC Phase 2 Profile Parameters514.6System parameters514.7Control parameters545Control Board LEDs556Button Learn-run sequences567Reference motion profile parameter table577.1PT400-CO587.2PT400-SS587.3PT400-2S587.4XIZI CO597.5Tianjin CO598Health Management60.3 / 438.1Events management608.2LED Blinking counts and event681 IntroductionThe service tool is a terminal that has a keyboard and a display to communicate via a serial interface. When connected to the Door Controller, the service tool allows the user to monitor status,error logs, configure parameters,enter commands and etc.The service tool front panel consists of a display and 16 keys. The display is a two-line,16 characters per line, liquid crystal display. Twelve of the keys are divided into twoparts. The upper part of the key is white; the lower part of the key is blue. To activate the white function on any key, just press the marked button. To activate the blue function on any key, use the combination of keys. First press SHIFT , and then press the intended key. For example, if the GO ON/GO BACK key is pressed, the GO ON function occurs. If the SHIFT key as well as the GO ON/GO BACK key is pressed, then the GO BACK function occurs.The connection to the NGSOK2 Door Controller is done by connecting SVT line into port P11 on the SPMDCB2Figure 11 Mechanical Design of Service Tool1.1 Power OnAfter power on, the Service Tool performs a self-test. After the successful test the serial communication to the SPMDCB2 is checked. Depending on the result of this test, a message is displayed.To enter the menu system the key,Module has to be pressed. To checkthe softwareversion of the Service Tool, press the SHIFT KEY and then Module.Figure 12Self test sequence1.2 Key Function Description The following symbols are used throughout the manual:ONfirst press SHIFT and then ONSELFTESTIN PROGRESSSELFTESTOK - MECS MODESELFTESTOK - MP2/3 MODEPower onSelf test passed;Communication establishedSelf test passed;no communicationGO ONkey GO ON to be pressedGOBACKfirst press SHIFT and then GOBACKDOWNfirst press SHIFT and then DOWN1key 1 to be pressed2key 2 to be pressed3key 3 to be pressedCLEARkey CLEAR to be pressedSELF TEST-OK- MECS MODEOTIS Service Tool8MODULE795FUNCTION46GO ON0CLEAR2SET13OFFGO BACKENTERONUPDOWNDISP INSEL OUTDISP STATEENT CALLTESTSHIFT KEY16 Characters2 line display.4 / 432 Software OverviewThe software for the Service Tool provides a menu system, which is organized as a tree structure. With the numeric keys and the keys MODULE, FUNCTION and SET you can easily move through the system. With the key CLEAR you can clear the most recently pressed key.2.1 Local and Remote Service tool2.1.1 Local SVT connectionAfter connecting the service tool to NGSOK2 directly, below display will be shown.To enter into sub menus, type 32.1.2 Remote SVT connectionIf Service tool is connected through other sub system Remote connection, after pressing module key and then pressing key 3 and the below door selection main menu is displayed.2.2 Menu OverviewAll functions are arranged in groups to simplify selection of the desired function. Afte。