EMC VPLEX安装实施方案

1、贵州师范大学VPLEX-LOCAL的硬件配置信息此次安装的VPLEX-Local有单台台VPLEX组成，VPLEX的硬件配置如下：1) 1个Engine2) 2个Director，每个Engine由两个Director组成3) 8个8Gb前端FC端口，每个Director包含一块前端FC卡，共4个8Gb的前端FC端口，由于交换机端口限制，本次使用4个前端FC端口（每个Directo上两个）。4) 8个8Gb后端FC端口，每个Director包含一块后端FC卡，共4个8Gb的后端FC端口。本次使用4个前端FC端口（每个Directo上两个）5) 4个可用的8Gb的VPLEX-Local级联FC端口，每个Director包含一块VPLEX-Local级联FC卡，共4个8Gb的级联FC端口，但是只有两个可用VPLEX-LOCAL的硬件介绍单台VPLEX的硬件布局VPLEX的ENGINE的硬件布局VPLEX-LOCAL的级联端口连接VPLEX-LOCAL拓扑结构VPLEX-LOCAL的FABRIC拓扑图VPLEX-LOCAL后端存储系统的配置META VOLUME的配置请注意每台VNX必须使用

2、两个RG，每个RG各提供两个80G LUN。Mirror和backup的meta volume LUN需分开RG存放。不推荐mirror 和 backup 放在同一个RG里。ClusterMeta VolumeStorageRAID GroupLUN IDRAIDSizeVPLEX_01Meta_Mirror_1VNX5400RG1800RAID1080GBMeta_Bcakup_1VNX5400RG1801RAID1080GBMeta_Mirror_2VNX5400RG0800RAID1080GBMeta_Backup_2VNX5400RG0801RAID1080GBLOGGING VOLUME的配置ClusterLog VolumeStorageRAID GroupLUN IDRAIDSizeVPLEX_01Loggin_Mirror_1VNX5400802RAID1010GBMirror 2VNX5400802RAID1010GBVPLEX-LOCAL安装配置流程VPLEX-LOCAL安装配置详细步骤在VPLEX-Local的安装配置过程中，有些命令在Manager Server

3、上运行，有些命令在VPLEX上运行，以下标志代表命令的运行场所：【MS_CLUSTER_1】: VPLEX_01的Manager Server的shell环境下运行【VPLEXCLI_CLUSTER_1】: VPLEX_01的VPlex的CLI环境下运行，在Manager Server的shell环境下，运行“vplexcli”命令进入该环境【MS_CLUSTER_2】: VPLEX_02的Manager Server的shell环境下运行【VPLEXCLI_CLUSTER_2】: VPLEX_02的VPlex的CLI环境下运行，在Manager Server的shell环境下，运行“vplexcli”命令进入该环境CLUSTER_1的安装配置CLUSTER_1的初始化配置1. 将配置用的笔记本电脑的网卡设置为通过DHCP获取IP2. 配置用的笔记本电脑通过网线连接到VPLEX_01的Manager Server的eth1网口3. 通过putty.exe或SecureCRT软件登陆到VPLEX_01的Manager Server上，Host IP：128.221.252.2，Conne

4、ct type：SSH，用户名：service，密码：MiDim7T 4. 设置Manager Server的主机名【MS_CLUSTER_1】# sudo /opt/emc/VPlex/tools/ipconfig/changehostname.py -n VPLEX-015. 重新登陆Manager Server，查看提示符或/etc/HOSTNAME文件内容，确认主机名更改成功【MS_CLUSTER_1】# cat /etc/HOSTNAME6. 运行vplexcli命令登陆到VPLEX_01，用户名为service，密码为MiDim7T【MS_CLUSTER_1】# vplexcli7. 配置Manager Server的管理公用IP地址【VPLEXCLI_CLUSTER_1】# management-server set-ip -i VPLEX_01_IP:VPLEX_NETMASK -g VPLEX_GATEWAY eth3【VPLEXCLI_CLUSTER_1】# ll /management-server/ports/eth38. 运行exit命令，退出VPLEX_01

5、到Manager Server，检查公用管理网络的连通性【VPLEXCLI_CLUSTER_1】# exit【MS_CLUSTER_1】# ping VPLEX_GATEWAY9. 配置NTP时钟服务器，同步时间【MS_CLUSTER_1】# vi /etc/ntp.conf; 设置外部server为NTP_IP【MS_CLUSTER_1】# sudo /etc/init.d/ntp restart【MS_CLUSTER_1】# date10. 运行exit命令，退出VPLEX_01的Manager Server【MS_CLUSTER_1】# exit启动CLUSTER_1的DIRECTOR，检查和确认版本信息11. 通过putty.exe或SecureCRT软件登陆到VPLEX_01的Manager Server上，用户名为service，密码为MiDim7T12. 运行vplexcli命令登陆到VPLEX_01，用户名为service，密码为MiDim7T【MS_CLUSTER_1】# vplexcli13. 启动VPLEX的Director，确认显示的director数量正确（2

6、个director）【VPLEXCLI_CLUSTER_1】# configuration connect-local-directors【VPLEXCLI_CLUSTER_1】# ll /engines/*/directors14. 检查VPLEX及每个Director的版本，确认符合版本控制要求【VPLEXCLI_CLUSTER_1】# version【VPLEXCLI_CLUSTER_1】# exit检查硬件运行状态15. 检查VPLEX及每个Director的版本，确认符合版本控制要求【MS_CLUSTER_1】VPlexPlatformHealthCheck确认检查结果符合下表：运行EZ-SETUP配置向导16. 运行EZ-Setup配置向导，完成以下方面的配置：【MS_CLUSTER_1】# vplexcli【VPLEXCLI_CLUSTER_1】# configuration system-setup提示选择What would you like to configure? 1. Configure a VPLEX Local (single cluster). 2. C

7、onfigure a VPLEX Metro (synchronous, 2 clusters). 3. Configure a VPLEX Geo (asynchronous, 2 clusters).Select your configuration choice. (1-3)2What would you like to configure? 1. Configure the first or only cluster. 2. Configure the second cluster of a VPLEX Metro implementation.Select your configuration choice. (1,2)1Are you sure you want to configure the first or only cluster? (yes/no):yesWould you like to configure the login banner? (yes/no):noWould you like to configure an authentication ser

8、vice provider to authenticate VPLEX users? (yes/no) no:noWould you like to configure this cluster to send event notifications to EMC? (yes/no) yes:noWould you like to configure this cluster to send system reports to EMC? (yes/no) yes:noWould you like to configure the cluster to run the SNMP Agent Service? (yes/no) no:noHow many years should the CA certificate remain valid before expiring? EMC recommends 5 years (maximum is 5 years). 5:5How many years should the host certificate remain valid befo

9、re expiring? EMC recommends 2 years (maximum is 2 years). 2:2Would you like to run the setup process now? (yes/no):yesPlease create a passphrase (at least 8 characters) for the Certificate Authority Key. Make a note of this passphrase as you will need it to configure a second cluster of a VPLEX Metro or Geo. Certificate Authority passphrase:guizhou_sfdxRe-enter the passphrase for the Certificate Authority Key:guizhou_sfdxPlease create a passphrase (at least 8 characters) for the Local Host Certificate Key. Make a note of this passphrase as you will need it later. Host Certificate passphr

《EMC VPLEX安装实施方案》由会员jiups****uk12分享，可在线阅读，更多相关《EMC VPLEX安装实施方案》请在金锄头文库上搜索。