颚式破碎机中英文说明书

1、PE500x750颚 式 破 碎 机JAW CRUSHER使 用 说 明 书OPERATING INSTRUCTION中华人民共和国THE PEOPLES REPUBLIC OF CHINA江苏天鹏机电制造有限公司JIANGSU TIANPENG ELECTROMECHANICAL MANUFACTURING CO., LTD.地址：江苏省海安县大公镇工业园区 网址：电话：0513-88758185 E-mail:邮编：226623 传真：0513-88759868目 录Contents一、用途Application1二、主要技术参数Main technical parameters1三、结构简述及装配Brief description of structure and assembly2四、安装、调整和试车Erection、adjustment and test run7五、使用和维护Operation and maintenance8六、安全、操作规程Safety and operation regulations11七、易损件零件明细表Wearing parts list 12八

2、、必须注意的事项Attentions 12九、润滑Lubrication13十、基础图Foundation drawing 14江苏天鹏机电制造有限公司为了确保破碎机正常工作，充分发挥其应有的性能，请您在使用破碎机前详细阅读本说明书，并按照说明书要求进行操作。In order to ensure normal operation of the crusher and fully bring out its performance, please you read the manual in detail before operating the crusher and operate it as per the requirements on the manual. 1.用途Applications本机为复摆式颚式破碎机，广泛适用于矿山、冶炼、建筑、公路，铁路、水利和化学工业等众多行业，处理粒度不大于425毫米，抗压强度不超过250兆帕的各种矿石和岩石粗碎或中碎作业。It is double-taggle jaw crusher; it is widely used for rough

3、-crushing or middle-crushing all kinds of ore and rock whose grain size is not more than 425mm and compressive strength is not more than 250Mpa in mineral、smelting、construction、highway、railway、water conservancy as well as chemical industries and other industries. 2.主要技术参数Main technical parameters2.1给料口尺寸(宽*长)Dimension of feeding port(W*L): 500*750mm2.2排料口宽度Width of discharge port: 50100mm2.3最大给料尺寸Max. feeding size:425mm2.4主轴转速Rotating speed of main shaft: 275r/min2.5生产能力Protective capacity: 28.5

4、62.5m3/h2.6电动机Motor 型号model: Y280M-6 功率power: 55 kW 转速rotating speed: 980r/min2.7外形尺寸(长*宽*高)Overall size(L*W*H): 1890*1916*1870mm2.8重量(不包括电机)Weight(except for motor): 10300kg注：破碎机的处理能力受各种因素的影响，诸如给料方式，物料的形状、粒度组成、物料的干、湿、软、硬程度等等。对于硬而脆的物料要比硬而韧的物料容易破碎；片状物料要比球状物料容易破碎，由大小不同粒度组成的混合料要比单一大粒度组成的物料容易破碎而获得较高的处理能力。相反，如果物料超过最大允许的进料粒度或者进料口堆满物料而出现阻塞现象时，往往就导致处理能力的降低。Notes: The processing capacity of the crusher is affected by several factors, such as feeding way, shape of material, granulometric composition, mois

5、ture content and hardness of material. For hard and crisp material is more breakable than hard and tough material. Slice material is more breakable than ball shape material. The mixture made up of different granularity is more breakable than that of the same granularity, so it gets higher processing capacity. On the contrary, if the material is larger than the maximum allowable feeding size or the feed inlet is blocked up, then it may lower the processing capacity.为了提高本机的处理能力和使用寿命，必须满足其均衡进料的要求。因

6、此在使用本机时需由喂料机与之配套。To improve the processing capacity and service life of this machine, we must satisfy the requirements of balanced feeding. Therefore, we must equip a feeder to match with this crusher when using it.本机标定的性能参数是以破碎干且中等硬度的岩石为准，其堆比重为1.6吨/立方米。The performance parameter of the crusher is decided by crushing dry and medium-hard rock, its bulk density is 1.6t/m3。3.结构简述及装配Structure description and assembling本机主要由:1机架部件；2固定颚板；3上边护板；4下边护板；5动颚部件； 6调整部件；7拉杆部件；8铁轨部件；9润滑部件；10基础部分等组成。The crusher

7、is mainly made up of the following parts:1. Frame components; 2. Fixedjaw plates; 3. Upper protection plate; 4.Down protection plate;5. Moving jaw components; 6.Adjustment components; 7.Pull rod components. 8. Rail components. 9.Lubricartion components; 10.Fundamental components.本机是以电动机为动力，通过电动机皮带轮，由三角皮带和槽轮驱动偏心轴，使动颚按预定轨迹作往复运动，从而将进入由固定颚板、活动颚板和边护板组成的破碎腔内的物料予以破碎，并通过下部的排料口将成品物料排出。The crusher is motor powered. By motor pulley, triangle belt and geneva wheel drive the eccentric shaft and make the movi

8、ng jaw move along a scheduled track back and forth. Then the material in the crusher chamber (which is made up of fixedjaw plate, moving jaw plate and edge plate) is crushed and the finished product is discharged through the below discharge opening.3.1机架部件Frame components颚式破碎机的机架，在工作中受到很大的冲击载荷。因此它应具有足够的强度和刚度。The frame of the jaw crusher must be of enough intension and stiffness, because it suffers from the impulsive load when working.机架为焊接件。机架的前墙装有由固定颚板螺钉紧固的固定颚板，机架的左、右内侧壁装有由螺钉紧固的上边护板和下边护板。活动颚板和固

9、定颚板均为优质高锰钢铸件，为延长其使用寿命，其形状设计成上、下对称，即当一端磨损后调头使用。The frame is weldment. The front wall of the frame is equipped with fixed jaw plate, and the left and right inside wall is equipped with upper edge plate and lower edge plate. The moving jaw plate and fixed jaw plate is of high manganese steel castings. In order to prolong its service life, the upper and lower shape is designed symmetry, so when one end is worn, the other end can be used.3.2动颚部件moving jaw component3.2.1结构特征structure feature：动颚为整体优质铸钢结构，其内孔以及槽等部位经过精确加工与检测，确保工作时安全、可靠。The moving jaw is o

《颚式破碎机中英文说明书》由会员cn****1分享，可在线阅读，更多相关《颚式破碎机中英文说明书》请在金锄头文库上搜索。