机器人专业词汇中英文对照.docx

机器人专业词汇中英文对照ACAS Applicator Cleaner Air Supply 雾化器清洗器供气pACS Applicator Cleaner Solvent Pilot 雾化器清洗器溶剂控制阀ACS Applicator Cleaner Solvent 雾化器清洗器溶剂ACVA Applicator Cleaner Vacuum Air 雾化器清洗器真空空气ACDA Applicator Cleaner Drying Air 雾化器清洗器干燥空气BEAR Bearing Air 轴承空气BAO Bearing Air OK 轴承空气正常BRAKE Brake Air Turbine 涡轮刹车空气pBW Bell Wash Pilot 旋杯清洗控制阀BWS Bell Wash Supply 旋杯清洗供应AIR Color Change Air Supply 换色空气供应SOL Color Change Solvent Supply 换色溶剂供应CP# Color Pilot (#) = Color 颜色控制阀（#）= 颜色DUMP Dump 排放DAT Drive Air Turbine 涡轮驱动空气E-STAT Electrostatics 静电pIW Injector Wash Pilot 注射器清洗控制阀IWS Injector Wash Supply 注射器清洗供应PAINT Paint 油漆PAP Purge Air Pilot 冲洗空气控制阀pCC Pilot Color Change 换色控制阀PCE Process Control Enclosure 工艺控制柜pDUMP Pilot Dump 排放控制阀PDP Power Distribution Panel 配电柜PIE Process Interface Enclosure 工艺接口柜PREG Pilot Regulator 调节器控制阀PR# Paint Return (#) = Color 油漆回路（#）= 颜色PS# Paint Supply (#) = Color 油漆进路（#）= 颜色pPS Purge Solvent Pilot 冲洗溶剂控制阀pTRIG Pilot Trigger 触发器控制阀PTS Pilot Trigger Supply 触发器供应控制阀RP Robot Purge 机器人净化SA1 Shaping Air (Bell Applicator) 成形空气（旋杯雾化器）SA2 Shaping Air (Bell Applicator) 成形空气（旋杯雾化器）SAP Shaping Air Pilot 成形空气控制阀SAS Shaping Air Supply 成形空气供气SCC System Control Console 系统控制柜TDP Turbine Drive Pilot (Bell Applicator) 涡轮驱动控制阀（旋杯雾化器）TURB Turbine Drive Supply 涡轮驱动供气Purge System Maintenance净化系统维护- Purge System Diagnostics净化系统诊断- Purge System Testing andCalibration净化系统测试和校准- Purge Cycle Troubleshooting净化循环排错?Color Changer Assembly换色器组件- Color Changer Valve Maintenance换色阀门维护?SolvAir Module Setup and Maintenance 溶剂空气模块设置和维护?3 Valve IK Gear Pump3阀门1K齿轮泵- Pump Block Pressure Sensor泵的压力传感器?Process Control Maintenance工艺控制维护- Fluid Presets Maintenance流体预设值维护- E-stat Presets Maintenance静电预设值维护- Preset Override Maintenance强制预设值维护- Color Change Maintenance换色维护?Pepperl & Fuchs ISB SettingsPepperl & Fuchs ISB设置?Robot Software Maintenance机器人软件维护- I/O Re-configurationI/O 重新配置- Robot File Copy机器人文件复制- Robot System Variables Editing Transducer Operations比例阀的操作- Shaping Air Control成形空气的控制- D/Q Shaping Air Control ModuleD/Q 成形空气控制模块- Turbine Speed Control涡轮速度控制- Keyence Digital Fiber SensorKeyence 数字光线传感器?Fluid Calibration - Beaker Method流体校准–量杯的方法?System Configuration Maintenance系统配置维护- System Colors Maintenance系统颜色维护- Styles Maintenance车型维护- Option Maintenance选项维护- PW3 SetupPW3 设置机器人系统变量编辑- Software Archive软件存档- Backup a Robot Image备份一个机器人镜像- Restore a Robot Image恢复一个机器人镜像?Paintworks III Software MaintenancePaintworks III软件维护- Creating a Norton Ghost 2003Boot Disk Set创建一个Norton Ghost2003 启动盘- Backing Up Your PAINTworks IIIGUI备份你的PAINTworksIII GUI。

Copying Your Ghost Image Filesto CDs把你的Ghost 镜像文件复制到CDs Restoring Your PAINTworks IIIGUI恢复你的PANITworks III GUIpAIR PAP Pilot input for Purge Air净化空气的驱动输入pSOLV PSP Pilot input for Purge Solvent净化溶剂的驱动输入AIR CCAS Purge Air supply input净化气源输入SOL CCSS Purge Solvent supply input净化溶剂供应输入pCC PCC Pilot for Color Changer operation. When this input is enabled, thepurge air and solvent mixture will be directed to the color changermanifold as aerated solvent.换色器操作的驱动这个输入被激活时，净化空气和溶剂混合物会直接通向换色器多只管，像充气的溶剂一样2T Output 2T Secondary output (used for Applicator Wash). Solvent or air or the aerated mixture is always available at this port. If it is not requiredin the system, the port must be plugged.二次输出（用于雾化器清洗）。

在这个端口一直有溶剂、空气或者混物如果系统没有要求，这个端口必须被塞紧1K Process Assembly with a Regulator 含调整器的1K 工艺组件EO-4696-511-000 Rev. A Sheet 1 of 1 EO-4696-511-000 Rev. A版第一页/共一页COLOR CHANGER (24 COLOR MAX.) 换色器(最多24种颜色)WASH 清洗INJECTOR 注射器WASH 清洗PAINT ENABLE 喷漆激活TRIGGER 触发器BELL WASH 杯头清洗PAINT 油漆SOLV/AIR 溶剂/空气AIR 空气RECOVERY 回收DUMP 排放2K Process Assembly with a Regulator Schematic 含调整器的2K工艺组件示意图EO-4696-517-000 Rev. C4 Sheet 1 of 1 EO-4696-517-000 Rev. C4版第一页/共一页COLOR CHANGER (4 COLOR MAX.) 换色器(最多四种颜色)INJECTOR WASH 注射器清洗PAINT ENABLE 喷漆激活TRIGGER 触发器BELL WASH 杯头清洗CAT 架子DUMP 排放FLUSH 齐平AIR1 空气1SOLV/AIR 溶剂/空气WASH 清洗SOL2 溶剂20-500 PSI 0-500 PSIApplicator Interface 雾化器接口ET-4696-890-001 Rev. A Sheet 1 of 1 ET-4696-890-001 Rev. A版第一页/共一页ORIGIN OF TOOL FRAME 工具坐标系原点BOLT HOLES 螺栓孔FAN 风扇FAN 风扇FACE PLATE 面板TOOL FRAME 工具架EDGE OF BELL CUP 杯头边缘SECTION A-A A－A截面SCRMO00000277N (6) SCRMO00000277N (6)M6 Craftech Scr. M6 工艺技术螺丝Torque to 1.25 Nm 转矩至1.25 NmPINLM005000012S PINLM005000012S工作特征备注最高运行电压90kV正常旋转速度20到45 kRPM最高旋转速度* 45 到60 kRPM喷漆正常流速0到300 cc/min最大流速500 cc/min正常喷漆应用压力90到120 psi最大喷漆应用压力150 psi粘度范围50到200 cps空气空气压强供应85 psi min空气供应过滤: 级别1 按照DIN ISO 8573-1空气消耗涡轮支承57 slpm涡轮在60，000 rpm** 119 slpm成形空气70到500 slpm密封空气0到50 slpm (通常不需要)电气能量供应120 v 50/60 HzTube Requirements 管道要求ET-4696-890-002 Rev. B1 Sheet 1 of 1 ET-4696-890-002 Rev. B1版第一页/共一页SECTION A-A A-A截面。