SST_PROFIBUS组态步骤(胡).doc

SST-PFB-SLC PROFIBUS CARD CONFIGURATION SET UP PROCEDURESST-PFB-SLC卡组态步骤DP SLAVE CONFIGURATION SETUP PROCEDURE:注意:使用SST-PBF-SLC作为从站组态时，只能使用超级终端连接 SST-PBF-SLC卡来进行配置，具体步 骤如下：1、 用钥匙把SLC的CPU打到PROGRAM 模式；2、 用RS-232电缆连接SST卡和电脑的COM接口；3、 打开超级终端（开始-程序-附件-超级连接）；4、 设置电脑COM 口的参数，波特率为115.2K,其它的设置为默认值，完成后会自动连接上 SST 卡；5、 此时，SST卡上的COMM和SYS灯会交替闪烁，说明SST卡进行了组态模式，可以进行从站 参数设置；6、 按压“ * ”键直到超级连接窗口出现 SST卡的数据说明；7、 键入“ HELP ”命令，会出现SST卡的设置菜单；8、 键入“ SHOWNET ”命令，可以查看SST卡上存在的组态参数；如果 ACTIVE的参数不是为0，则要使用命令：ACTIVE 0 ； （ ACTIVE为0作为从站，为1时作为主站）9、 设置从站的波特率，命令：BAUD ##（注意波特率要和主站的一致，如 9.6K，则输入BAUD 9K6，12M 则输入：BAUD 12M）10、 设置从站的地址，命令：LOCSTN ## ；11、 设置发送和接收文件的长度，使用命令： SLVTXLEN # # # （发送），SLVRXLEN # # # （接收）；第一位# :发送，接收数据地址的偏移量（0~31）;第二位#:发送，接收数据的输入，输出字的长度（0~32）;第三位# :发送，接收数据在 M0 , M1上字的长度（0~122）;12、 完成后，用命令：UPDFLASH，把组态保存到SST卡上；13、 用命令：EXIT，退出组态模式，并断开与超级连接的通讯；注意：进入组态模式后，一定要用 EXIT命令退出，否则，SLC运行时，CPU会出现报错；14、 关闭超级连接程序；1. Place SLC processor in program mode.2. Connect to SST card via serial port on PC to SST card program port (male pin)3. Open Hyper Terminal on PC.4. Con figure COM 1 com muni cati on. Not ing that card will automatically detect baud rate up to 115k.5. Conn ect to the SST card. The COMM and SYS will flash red in dicat ing com muni cati on is in itialized.6. Depress * key many times, until the screen displays the card data.7. Type “ HELP , a help menu will appear.8. Type “ SHOWNET, the existing configuration of the card will appear.9. Set up Profibus Baud rate “ BAUD #” , Type fcHELPNEite setpoints.10. Set up Profibus station number “LOCSTN # “ Type “ HELPNET for station instructions.11. Set up file length SEND and RECEIVE data length. Type “ HELPSLV for instructions.12. Update flash memory, by typing “ UPDFLAS” , then depressing the ENTER key.13. Stop com muni cati on to the card by typ ing “ EXIT”sinigetiheieiNTER key.14. Shut down HYPER TERMINAL.Notes to the above in structi ons:1. When con figuri ng the SST-PFC-SLC card as a SLAVE. The card can only be con figured by a commu ni catio n emulation program (HYPER TERMINAL).2. Whe n used only as a slave, the SST card con figurati on is mi ni mal. Requiri ng only the STATION #, BAUD rate and SEND and RECEIVE con figured. The rest of the opti ons on the SST card are reserved for MASTER con figuratio n.3.It is very importa nt to in itiate the EXIT comma nd, before disc onnecting from the SST card. If you do not EXIT correctly. The PLC processor will fault whe n select ing RUN mode. Because the SST card still thi nks it is talk ing to the HYPERTERMINAL program.4. Refer to the SST-PFB-SLC , Users Guide Versio n 2.4 for detailed in structio ns. See Chapers 4,5 and 7.5. Whe n con figuri ng the SST card as a slave. The SST Profibus COMM software cannot be used. This software is on ly used whe n a MASTER card is con figured. This software helps assist in finding the GSD file for the SST card.6. The GSD file is critical for the Profibus con figuratio n. Whomever is con figuri ng the profibus will n eed the GSD file for this card. Attached below is the GSD file for this card. The file in dicates set up in formatio n needed for the Profibus MASTER.SST-PFC-SLC GSD FILE:; Device Data File for SST-PFB-SLC Slave; Copyright (c) 1997-2003 SST, a division of Woodhead Canada Ltd. ; Rev 1.8#Profibus_DPGSD_Revision = 1Vendor_Name = "SST"Model_Name = "SST-PFB-SLC"Revision = "Rev 1.8"Ident_Number = 0x0852Protocol_Ident = 0Station_Type = 0FMS_Supp = 0Hardware_Release = "1.0"Software_Release = "1.85" ; Supported baudrates 9.6_supp = 1 19.2_supp = 193.75_supp = 1187.5_supp = 1500_supp = 11.5M_supp = 13M_supp = 16M_supp = 112M_supp = 1; Maximum responder time for supported baudratesMaxTsdr_9.6 = 60MaxTsdr_19.2 = 60MaxTsdr_93.75 = 60MaxTsdr_187.5 = 60MaxTsdr_500 = 100MaxTsdr_1.5M = 150MaxTsdr_3M = 200MaxTsdr_6M = 200MaxTsdr_12M = 200 ; Supported hardware featuresRedundancy = 0Repeater_Ctrl_Sig = 224V_Pins = 0; Slave SpecificFreeze_Mode_Supp = 0Sync_Mode_Supp = 0Auto_Baud_Supp = 1Set_Slave_Add_Supp = 0; Maximum length of user parameterUser_Prm_Data_Len = 0 ; supports up to 25 ext user parameters set to 0 because of comprofibus and step7 ; Default user parameter string;User_Prm_Data = 0x00 ;# of defaults specified here must match # specified forMaximum length of user paramter dataSlave_Family = 0Min_Slave_Intervall = 2Modular_Station = 1Max_Module = 32 ;122 words Max, I/O must be word formatMax_Input_Len = 244Max_Output_Len = 244Max_Data_Len = 488Max_Diag_Data_len = 32Module = " 1 Word In " 0x50EndModuleModule = " 2 Words In " 0x51 EndModuleModule = " 4 Words In " 0x53EndModuleModule = " 8 Words In " 0x57EndModuleModule = "12 Words In " 0x5bEndModuleModule = "16 Words In " 0x5fEndModuleModule = " 1 Word Out" 0x60EndModuleModule = " 2 Words Out" 0x61EndModuleModule = " 4 Words Out" 0x63EndModuleModule 。