小功率面板灯300x300规格书.doc

小功率面板灯300x300规格书SPECFICATION 规格书Product Name： LED Panel Light （3528LED, 168PCS） Model:: CPS-MB-X13W-07一、 MAIN SPECIFICATIONS（T=20°C）Page 1 of 7二、 Packing（包装）：三）Features（特点）： Energy saved up to 50%・ high brightness evenlighting output・节省50%能源，亮度高，出光均匀探 Wide range of input voltage: AC100-240V宽电压工作AC100-240VInstant start, no flickering, no humming启动快，没有闪烁现象，没有噪音New high efficiency constant current driver 最新的高效恒流驱动器 探 Special circuit design, each group of LEDs work separately, avoidi ng any problem of lighti ng output caused or influe need by single faulty LED专业电路设计，每组灯独立工作，可避免单一的坏灯影响整体的出光 效果。

探 No electrical wave,conforming to CE抗电波干扰，符合CE要求Green environmental protection, lead-free material, conforming toROHS无铅，绿色环保，符合ROHS要求 探No RF interference不受无线电 干涉Page 2 of 7四、 Applications（应用范围）：探 Hotels （酒店）探 Conference/Meeting rooms （会议室）探 Factories & Offices （工厂或办公室）探 Commercial Purposes （商业用途）探 Residential/lnstitution Buildings （住宅及公共设施）探Schools,Colleges & Universities （学校）探 Hospitals （更院）五、 Light Distribution Graph （配光曲线图）Page 3 of 7六、 Fixing Ways （安装方式）：七、 Safety Notice for Using （安全使用注意事项）：探 Please always use the luminaire out of its package产品只能在包装外使用Before starting use of the fixturezpls check if the fixture was damagedduring transportaion使用前检查有没有损坏Any maintenance should be performed by trained professionals only不耍尝试自己维修，只能专业人士去维修。

探 Never leave children unattended in the vicintity of the lights and do notallow them To play with electrical devices.Page 4 of 7让小孩远离产品，更不要让小孩接触带电设备Never allow the fixture to come into contact with open flames or exter nalheat sources・产品要远离明火或高温物体探 The products need to re-repair inspection or special treatment ofretirement after service time・产品过了使用期限，需要重新维修检查，或报废处理八、Installation（安装注意事项）:This product should be in stalled by trai ned electricia ns产品的安装必须是专业电工探 Check integrality of the products when unpack the packing.从包装箱里拿出时要检查产品的完整性。

The distanee between the light and any flammable materials must notbe less tha n 0.2m ・ The dista nee betwee n the upper part of the in stalledlight and the ceiling must not be less tha n2cm.The light must not be in stalled into ceilings or walls that contain heat-insulating material. The main cable must not connect with the low voltage cable or the surfacemounted lights.产品与易燃材料要保证至少0.2M的距离，要保证被安装的天顶有2 厘米高的间隙，灯具不能全部安装在天顶里面或有热源的墙边，要注意 低压电与高压电分开走线Guide the lights' connecting cables through the drilled-out hole,and fixthe surface mounted ,lights with the pre-fitted clips. Make sure that these are securelyconnected to the base material.灯具上的连线可以从钻孔中通过和灯具后面的连线可以用电线夹固 定，要确保固定牢固。

探 When laying the cables, make sure that the cables and plugs are notPage 5 of 7subjected to any tensile or twisting forces・ Fit the cable tension relieving mechanisms to the connection points of the surface-mounted lights. Do not kink cables. Output cables should be laid separately and at adistanee from other cables・要确保灯具的电源线有足够的长度，不要受到张力或切向力安装灯 具的连线时避免过大的拉力，不要使连线打结输出连线要注意区分，不 耍和其它灯具混淆探 After installation, connect the transformer to the mains supply安装好后，将灯具低压插头与开关电源低压插头进行连接Proceed by connecting the wiring cables to the luminaries. Usually,thebrown (or black) wire is the Live wire, connect it with the terminal marked "L". The blue wire is Naughty wire,connect it with the terminal marked "Nn.将灯具的开关电源尾巴连线与市电进行连接，通常棕色线(黑色)线 为火线，蓝色线为零线。

探 Use only the LED drover in eluded, and do not corm ect thesurface・mounted lights to other loads.耍使用灯具的LED专用驱动器，不耍和其它的灯具混用Do not remove the name plate of the power suply and driver of the light不要将灯具电源，驱动器的铭牌撕掉Page 6 of 7Notes:Non・professionals are not allowed to disassemble and maintain the products.We have the right not to provide after-slae service if unauthorized disassembly and maintenance happens to the products・非专业人员不得进行拆卸，维修，我司有权对私自拆卸，维修的产品 不给于更换或保修服务SHENZHEN CREP OPTOELECTRONICS CO^LTDAddress:深圳市宝安区石岩华半圳宝工业园Zhe nbao In dustrial Zon e?Shiya n Town^ao'anDistrict,She nxhe n,Gua ngdon g’Chi naTel:18664251138 李先生Website： http://www.crep-Page 7 of 7。