Cisco路由器配置实例经典

1、word实训报告实训一 路由根本配置1、实验目的：路由器根本配置与ip设置2、拓扑结构图RFRFZZ3、实验步骤Router1Routeren 用户模式 进入特权模式 Router#conf t 特权模式 进入全局模式 Enter configuration mands, one per line. End with TL/Z.Router(config)#host rznn1 改名字为 rznn1rznn1(config)#int fa0/0 进入fa0/0端口 设置ip地址 rznn1(config-if)#no sh 激活rznn1(config)#int fa0/1rznn1(config-if)#ip add 192.168.1.1 rznn1(config-if)#no shrznn1(config-if)#exitrznn1(config)#exitrznn1#copy running-config startup-config 保存 Destination filename startup-config? startup-configrznn1#conf trznn1(

2、config)#enable secret password 222 设置密文rznn1#show ip interface b 显示Interface IP-Address OK? Method Status ProtocolFastEthernet0/0 192.168.11.1 YES manual up upFastEthernet0/1 192.168.1.1 YES manual up upVlan1 unassigned YES manual administratively down downrouter 2outerenRouter#conf tEnter configuration mands, one per line. End with TL/Z.Router(config)#host rznn2rznn2(config)#int fa0/0rznn2(config-if)#no shrznn2(config)#int fa0/1rznn2(config-if)#no shRznn2#copy running-config startup-config 保存 D

3、estination filename startup-config? startup-configrznn2(config-if)#exitrznn2(config)#exitrznn2#conf trznn2(config)#enable secret 222rznn2#show ip interface b Interface IP-Address OK? Method Status ProtocolFastEthernet0/0 192.168.11.2 YES manual up upFastEthernet0/1 192.168.2.1 YES manual up upVlan1 unassigned YES manual administratively down down实训二1、远程登录、密码设置与验证为路由器开设telnet端口，PC机可以远程登陆到Rznn3(Router 1)拓扑结构图RP步骤 rznn3rznn3enrznn3#conf tEnter configuration mands, one per line. End with TL/Z.rznn3(

4、config)#no ip domain lookuprznn3(config)#line cons 0rznn3(config-line)#password znnrznn3(config-line)#loginrznn3(config-line)#no exec-trznn3(config-line)#logg syncrznn3(config-line)#exitrznn3(config)#int fa0/0rznn3(config-if)#no shrznn3(config-if)#exitrznn3(config)#line vty 0 4 打通五个端口rznn3(config-line)#password cisco 设置密码rznn3(config-line)#login 保存 rznn3(config-line)#exit4、测试：实训三 命令组1、目的：八条命令 no ip domain lookupline cons 0passwordloginno exec-tlogg syncshow versionreloadcopy running-config start

5、up-configshow cdp neighbors)2、拓扑结构图RR3、步骤rznn1#conf tEnter configuration mands, one per line. End with TL/Z.1、rznn1(config)#no ip domain lookup 取消域名查找转换2、rznn1(config)#line cons 0 打开cons 0端口3、rznn1(config-line)#password znn 设置密码为 znnrznn1(config-line)#login 保存rznn1(config-line)#no exec-t 设置永不超时4、rznn1(config-line)#logg sync 产生日志5、rznn1#show version 显示思科路由系统版本信息Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T1, RELEASE SOFTWARE (fc2)Technical Support: .cisco./techs

6、upportCopyright (c) 1986-2007 by Cisco Systems, Inc.piled Wed 18-Jul-07 06:21 by pt_rel_team6、rznn1#show cdp neighbors 查看路由器连接的相邻路由器的相关信息Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - PhoneDevice ID Local Intrfce Holdtme Capability Platform Port IDrznn2 Fas 0/0 139 R C2800 Fas 0/07、rznn1#copy running-config startup-config 保存刚刚指令Destination filename startup-config? startup-configBuilding configuration.OK8、rznn1#reload 重启路由器Proceed with reload? confirmSystem Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)Copyright (c) 2000 by cisco Systems, Inc.cisco 2811 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memorySelf depressing the image :# OK Restricted Rights Legendrznn1#show ip interface bInterface IP-Address OK? Method Status ProtocolFastEthernet0/0 192.168.11.1 YES manual up upFastEthernet0/1 192.168.1.1 YES manual up upVlan1 unassigned YES manual administratively down d

《Cisco路由器配置实例经典》由会员cl****1分享，可在线阅读，更多相关《Cisco路由器配置实例经典》请在金锄头文库上搜索。