玻璃钢管安装工艺中文版Installation Manual-Marine in Chinese with NOV Logo.docx

辐基斯玻璃钢管安装指导(BONDSTRAND 系列 — 船舶及海洋工程)设计参考编码:文 档 代 码: INS-MAR-01日 期: 27th FEB- 2012版 本 号: Rev. 6目 录1.前言...................................................................................................................................52.参考资料...........................................................................................................................53.管系布置...........................................................................................................................63.1管系布置...............................................................................................................63.2管段分割...............................................................................................................63.3导电性和接地（仅适用于导电玻璃钢管系统).................................................64.玻璃钢管支架...................................................................................................................74.1支架布置基本原则...............................................................................................74.2支架跨度...............................................................................................................74.2.1最大支架跨度...............................................................................................74.2.2双 O 型圈膨胀节处的支架跨度..................................................................84.2.3机械膨胀节处的支架跨度...........................................................................94.3锚固支架上的轴向载荷.......................................................................................94.4支架类型及详图.................................................................................................104.4.1滑动(导向)支架..........................................................................................104.4.2固定支架（轻微锚固）.............................................................................114.4.3锚固支架.....................................................................................................124.4.4法兰托架.....................................................................................................125.到货验收、搬运和存放.................................................................................................145.1到货验收.............................................................................................................145.2搬运.....................................................................................................................145.3运输.....................................................................................................................145.4吊装.....................................................................................................................145.5存放.....................................................................................................................155.5.1玻璃钢管存放.............................................................................................155.5.2管件存放.....................................................................................................15Page 1 of 37Rev.65.5.3 制成管段 155.5.4 胶粘剂 155.5.5 配件 155.5.6 工具 156. 玻璃钢管的安装 166.1 胶粘剂连接方式 166.1.1 胶粘剂连接方式所用的特殊工具 166.1.2 粘接程序 166.2 法兰连接 176.2.1 法兰垫片 176.2.2 螺栓螺母 176.2.3 法兰装配 176.2.4 法兰安装允许偏差 176.2.5 建议螺栓扭矩 186.2.6 紧固顺序 196.3 双 O 型圈接头的装配 206.3.1 准备工作和预先装配 206.3.2 插接深度和配件 206.3.3 装配前的检查 216.3.4 装配 DOF－DOM 接口 226.3.5 装配双 O 型圈膨胀接头 226.3.6 辅件的存放 236.4 装配机械式膨胀接头 246.4.1 准备工作和预置 246.4.2 装配前检查 256.4.3 装配 256.5 与其它材料的连接时的注意事项 26 Page 2 of 37 Rev.66.6与设备、储罐、压力容器的连接.....................................................................266.7玻璃钢管相连最大允许偏差.............................................................................276.8钢结构分段中安装管系.....................................................................................277.玻璃钢系统的液压试验.................................................................................................297.1系统液压试验.....................................................................................................297.1.1液压试验总说明.........................................................................................297.1.2试验介质和试验压力.................................................................................297.1.3检查、验收标准及认可.............................................................................297.1.4温度影响.....................................................................................................297.1.5压力试验后系统复位........................。