APC安装维修手册.pdf

American Power Conversion APC UPS安装维修手册 一、UPS之装设 1.地线 1)基本上，要使UPS有防雷击能力而不损毁，一定要有地线故APC强烈建议使用者安装地线 2)Smart-UPS背板有一 “ Site Wiring Fault ” 红色LED此灯亮起时表示地线不良，可能为以下三种情形之一： z 无地线 z 极性颠倒 z 中线过载 2.插头 1)2200VA以上之UPS其电线电流负荷量达15A以上，因此其插头为20A以上这种情况下，以 SU3000 为例，自配电盘的保险丝开始，配线、插座、UPS 插头、UPS电源线，UPS 断电器等全部须能负荷 30A 以上，才是安全的用电环境2200VA 以上随机附有适用插座，请参阅下表 机型 插头型式 插座型式 最大电流 额定电压 SU700 SU1000 SU1400 SU1400RM NEMA 5-15 P NEMA 5-15 R 15A 125V SU2200 SU2200RM3U NEMA 5-20 P NEMA 5-20 R 20A 125V SU3000 NEMA L5-30 P NEMA L5-30 R 30A 125V SU2200XL NEMA 5-30 P NEMA 5-30 P 30A 125V MX3000 NEMA L6-30P NEMA L6-30R 30A 250V MX5000 NEMA L6-30P NEMA L6-30R 30A 250V 5-15P 5-20P L6-20P L5-30P L6-30P 2)若客户选购此种大 VA 数之 UPS 只为 Runtime 长，事实上负载并不大时，可以只更换插头。

3.扩充卡安装 1)安装扩充卡前，请先将UPS放电Smart-UPS） 2)如遇UPS有任何不正常情况，请先移除所有连接的扩充卡再行测试 4.装设完成 1.安装完成后开机，UPS即开始自我测试任何时候怀疑Smart-UPS有不正常情况，请尝试冷启动建议安装完先充电几小时） 2.建议以UPS开关为总开关 二、软件安装 1.安装PowerChute Plus 1)自光盘安装 z 　 选择安装PowerChute或 PowerNet z 　 选择PowerChute for Windows or Windows 95或 for NT z 　 如选择NT则会先Stop UPS Service z 　 选择Install Directory z 　 选择UPS Model Type：SmartUPS, BackUPS, Matrix z 　 选择Com Port 2)自APC网站上下载的程序安装 2.No Communication问题 z 　 确定Cable已确实接好，并已打开UPS开关 z 　 确定只有UPS在使用指定的COM Port z 　 确定使用的Cable是正确的。

软件 Signaling Type Cable PowerChute Plus (except UNIX) simple signaling 940-0020B 灰PowerChute Plus for UNIX simple signaling 940-0023A PowerChute Plus (except SGI Irix)advanced signaling 940-0024C 黑PowerChute Plus for SGI Irix advanced signaling (only) 940-0049A 1)Windows NT I. 确定UPS Service已启动 II.确定Com Port的设定无误 z 　 NoSerialMice statement is included in Boot.ini. z 　 COM1：Address=3f8，IRQ=4 ；COM2：Address=2F8，IRQ=3 z 　 Disable FIFO z 　 确定Modem及RAS的COM Port无误 III. 确定pwrchute.ini档中的几个参数：(假设Com1) [UPS] SignallingType=Smart PortName=COM1 AutoUpsRebootEnabled=Yes BatteryReplacementDate=12/09/96 UpsPollInterval=4 2)Novell Netware I. 确定Pwrchute.nlm是否在执行 ? 如没有，请load。

II. 请检查Com Port设定 先unload pwrchute.nlm，再unload AIOCOMX.NLM (如用COM 1) LOAD AIOCOMX INT=4 PORT=3F8 NOFIFO III.请确定pwrchute.ini档中的几个参数：(假设Com1) [UPS] SignallingType=Smart HardwareType=1 BoardNumber=0 PortNumber=0 三、Smart-UPS 面板&操作 Front Panel電池電量/輸入電壓顯示燈超載顯示燈電池供電顯示燈負載顯示燈開 /自我測試更換電池顯示燈SmartTrim自動降壓顯示燈自動升壓顯示燈SmartBoost供電正常顯示燈關85%67%50%33%17%100% 13280% 12360% 11540% 10720% 98Rear Panel地線不良顯示燈模式顯示燈模式選擇鈕電腦介面埠SmartSlot外接擴充槽自動斷電器1.自我测试 2.停电 3.冷启动 4.不同输入电压 （自动升降压SmartBoost & SmartTrim） 5.更换电池 四、Smart-UPS 维修 1.可先尝试冷启动，若无法冷启动，则UPS为故障。

2.可先去除所有配件，以简化问题 3.请检查背板的自动断电器（Circuit Breaker）有无跳起可能因为超载） 4.如UPS有冒烟、烧焦或焦味，则UPS为故障 5.如UPS面板灯全闪，则UPS为故障 6.如更换电池灯号亮起，可先将UPS充电整夜，再进行自我测试 7.如超载灯号亮起，请减低负载 8.Smart-UPS英文说明书上问题处理表 Problem Possible Cause SolutionUPS will not turn on.On/test button not pushed. Press the on/test button to power the UPS and the loadUPS input circuit breakertripped.Reduce the load on the UPS by unplugging equipment andreset the circuit breaker by pressing the plunger back in.Very low or no utilityvoltage.Check the AC power supply to the UPS with a table lamp. Ifvery dim, have the utility voltage checked.UPS will not turn on or off.Computer interface oraccessory problem.Disconnect the computer interface or accessory. If the UPSnow works normally, check the interface cable, the attachedcomputer, and the accessory.UPS operates on-battery eventhough normal line voltage isthought to exist.UPS's input circuit breakertripped.Reduce the load on the UPS by unplugging equipment andreset the circuit breaker.Very high, low, or distortedline voltage.Test the input voltage with the utility voltage display. Seesection 5.6. Inexpensive fuel powered generators can distortthe voltage. If acceptable to the load, reduce the UPS'ssensitivity. See section 5.9.UPS beeps occasionally. Normal UPS operation. None. The UPS is protecting the load.UPS does not provide expectedback up time.The UPS's battery is weakdue to recent outage or isnear the end of its servicelife.Charge the battery. The UPS's batteries require rechargingafter an extended outage. Batteries wear faster when put intoservice often and when operated at elevated temperatures. Ifthe battery is near the end of its service life, consider replacingthe battery even if the replace battery indicator is not yet lit.The UPS is overloaded.Check the UPS's load display. See section 5.4. Unplug lessneeded equipment, such as printers.Front panel indictors flashsequentially.The UPS has been shut downby remote control.None. The UPS will restart automatically when utility powerreturns.All indicators are lit and theUPS emits a constant tone.Internal UPS fault.Do not attempt to use the UPS. Turn the UPS off and have itserviced immediately.The UPS operates normally, butthe site wiring fault indicator islit.Building wire error such asmissing ground or hot toneutral wire reversal.Have a qualified electrician correct the building wiring.Low battery light is on and theon-line light is off.The UPS is shut down andthe battery is discharged froman extended power outage.None. The 。