丰田发动机机械参数手册(93~99).docx

第一节丰田车系、发动机匹配表发动机型号匹配车型匹配年款5S-FECamry1993-1999Celica「1993-19993VZ-FECamry1993ES30019934A-FECelicaP1993Corolla1993-19973S-GTECelica19937A-FECorolla1993-1997CelicaP1994-19971FZ-FELand Cruiser1993-1997LX4701996-19972TZ-FEPreviaP1993-19951MZ-FECamryP1994-1999Avalon1995-1999ES3001994-19991ZZ-FECorollaP1998-19992UZ-FELand Cruiser1998-1999LX4701998-19992JZ-GEGS3001993-1999SC300P1993-19991UZ-FELS4001993-1999SC4001993-1999GS4001998-1999二、发动机参数1 . 5S-FE、3VZ-FE、4A-FE、7A-FE 型发动机参数表一一一一发动机型号 项目5S-FE3VZ-FE4A-FE7A-FE最大功率(Hp/r - Min -1)135/5400185/5200115/5600115/5600最 大 扭 矩(Ft - Lbs/r • Min -1)145/4400195/4400115/2800115/2800缸径x行程87.1X 90.987.4 X 82.081 X 7781 X 85.5汽缸排量（L）2.23.01.6P 1.8压缩比9.5: 19.6: 19.5: 19.5: 1点火次序点火提前角（° ）汽缸压缩压力（kPa）汽缸缸径187.000-87.01087.500-87.51081.001-81.01081.001-81.010287.010-87.02087.510-87.52081.010-81.02081.010-81.020387.020-87.03087.520-87.53081.020-81.03081.020-81.030主轴承孔内径159.020-59.02668.010-68.016259.026-59.03268.016-68.022359.032-59.03868.022-68.028汽缸最大失圆度和锥度0.1010.101汽缸最大平囿翘曲度0.050.050.050.05汽缸盖最大 翘曲度汽缸体面0.050.0990.050.05进排气歧 管面0.080.0990.100.10气门座宽度进气门0.99-1.400.99-1.401.0-1.41.0-1.4排气门0.99-1.400.99-1.401.0-1.41.0-1.4气门座锥角（° ）45454545气门导管汽 缸盖孔内径进气门(1)11.000-11.02711.026 （许用极限）11.026 （许用极限）排气门11.000-11.02711.026 （许用极限）11.026 （许用 极限）气门导管内径6.010-6.0306.010-6.0306.010-6.0296.010-6.029气 门 杆 到 导 管 油 隙进气 门标准值0.025-0.0600.025-0.0600.025-0.0610.025-0.061许用极限0.0800.0800.080.08排气 门标准值0.030-0.0650.030-0.0650.030-0.0660.030-0.066许用极限0.0990.0990.100.10气门锥角（° ）44.544.54545气门边 度（极缘厚 限值）进气门0.500.500.500.50排气门0.500.500.500.50气门整修长度进气门 限）（使用极97.1094.6086.9586.95排气门（使用极 限）98.0094.4087.3587.35气门杆直径进气门5.970-5.9855.970-5.9855.969-5.9855.969-5.985排气门5.965-5.9805.965-5.9805.96-5.98气门间隙进气门0.19-0.280.13-0.230.15-0.250.15-0.25排气门0.28-0.380.27-0.370.25-0.350.25-0.35气门弹簧自由长度41.96-41.9941.4038.5738.57负载长度16.7-19.5kg/34.7017.2-19.1kg/33.3016.9kg/31.7 (气门关闭)16.9kg/31.7（气门关闭）不垂直度2.002.002.02.0进气凸轮轴 轴向间隙 （2）标准值0.046-0.099许用极限0.120排气凸轮轴 轴向间隙 ⑵标准值0.030-0.0850.035-0.090[0.035-0.090许用极限0.0990.100.10凸轮轴轴向 间隙（3）标准值0.033-0.080许用极限0.120齿轮背隙标准值0.020-0.2000.020-0.200许用极限0.3000.3000.300.30凸轮轴轴颈直径26.959-26.97526.949-26.96524.949-24.965（排气凸轮轴1 号轴径）22.949-22.965（其它轴径）24.949-24.965（排气凸轮 轴1号轴径） 22.949-22.965（其它轴径）凸轮轴最大径向圆跳动0.0400.060凸轮轴轴颈 油隙标准值0.025-0.0620.035-0.0720.035-0.0720.035-0.072使用极限0.0990.0990.100.10凸 轮 轴 凸 轮 高 度进气标准值42.010-42.11042.160-42.26041.910-42.01041.910-42.010使用极限41.90042.01041.5041.50排气标准值40.060-40.16041.960-42.06041.960-42.06041.960-42.060使用极限39.95041.81041.5541.55挺杆孔直径31.000-31.01831.000-31.01831.000-31.02531.000-31.025挺杆直径30.966-30.97630.966-30.97630.966-30.97630.966-30.976挺杆油隙标准值0.024-0.0520.020-0.0520.024-0.0590.024-0.059［许用极限0.0700.0800.070.07曲轴轴向间 隙标准值0.020-0.2200.020-0.2200.020-0.2210.020-0.221使用极限0.3000.3000.3000.300曲轴径向圆跳动0.0600.0600.0500.050主轴承轴颈 直径054.998-55.00363.996-64.00047.994-48.00047.994-48.000154.993-54.99863.990-63.99647.988-47.99447.988-47.994254.988-54.99363.986-63.99047.982-47.98847.982-47.988主轴径失圆度0.0200.0200.0200.020主轴径锥度0.0200.0200.0050.005主轴承 油隙（3 号轴 径）标 准 曲 轴标准值0.025-0.0440.028-0.0560.015-0.0330.015-0.033许用极限0.0800.080加 大 0.25标准值0.027-0.0670.028-0.080许用极限0.0800.080主轴承 油隙 （除3 号轴 径）标准曲轴标准值0.015-0.0340.028-0.0560.015-0.0330.015-0.033许用极限0.0800.080加 大 0.25标准值0.019-0.0590.028-0.080许用极限0.0800.080主轴承厚度（3号主轴 承）11.9920-1.99501.989-1.99221.9950-1.99801.992-1.99531.9980-2.00101.995-1.99842.0010-2.00401.998-2.00152.0040-2.00702.001-2.004主轴承厚度（其它主轴 承）11.9970-2.00001.989-1.99222.0000-2.00301.992-1.995 132.0030-2.00601.995-1.99842.0060-2.00901.998-2.00152.0090-2.01202.001-2.004连杆轴承厚 度11.484-1.4881.484-1.4881.486-1.4901.486-1.49021.488-1.4921.488-1.4921.490-1.4941.490-1.49431.492-1.4961.492-1.4961.494-1.4981.494-1.498连杆轴承轴颈直径51.985-52.00054.986-55.00039.985-39.99947.985-48.000连杆轴承失圆度和锥度0.0200.0200.0050.005连杆轴 承油隙标 准 曲 轴标准值0.024-0.0550.028-0.0650.020-0.051。