上海电影院修缮安装工程监理细则.doc

Manipulator is now used as a industrial robots in use, the control objectives often appear often in industrial automation. Industrial automation technology has gradually matured, as mature a technology line has been rapid development in industrial automation as a separate subject. Manipulator application began to filter into welding, logistics, mechanical processing, and other industries. Especially at high or very low temperatures, full of poisonous gases, high radiation case, robot in similar circumstances showed great use also brings great convenience to the staff. Precisely because of this robot to get people's attention began to be a high degree of development. Labor rates, working conditions, labor intensive aspects of promoting development. Both at home and abroad to develop the PLC (programmable logic controller) is in various special circumstances and under special conditions set for mechanical devices. Now turned on the development of the microelectronics automatic control technology and the rapid development of the trains, the success of PLC hardware software and simulation control win big and successful development, now continues to develop as a factory automation standards. Because robots are good development of the technology makes a good optimization of productive capital, and robot shows this unique advantages, such as: has good compatibility, wide availability, hardware is complete, and programming that can be mastered in a short time, so in the context of industrial PLC applications became ubiquitous. Manipulator in many developed country agriculture and industry has been applied, such as the use of mechanical harvesting large areas of farmland, repeated operations on the high-speed line that uses a robotic arm, and so on. Today, the high level of automation combined with restrictions on the manipulator development level is slightly lower than the international. The design is mainly arm welding machine by PLC Automation control. This of design let designers on in school by learn of has a must of consolidation, understand has some usually didn't opportunities awareness in world range within some leading level of knowledge has has must awareness, hope designers can in yihou of design in the can success of using in this design in the proceeds of experience 1.2 manipulator in both at home and abroad of research profile automation mechanical arm research began Yu 20th century medium-term, after years with with computer and automation technology of development, Makes mechanical arm on the Grand stage of industrial automation and shine, gradually became an industrial evaluation standards, and its importance can be seen. Now original robotic arm spent most of mass production and use on the production line, which is programmed robotic arm. As the first generation of manipulator position control systems main features, although not back several generations that can detect the external environment, but can still successfully complete like welding, painting, delivery as well as for materials simple movements. Second generation mechanical arms are equipped with sensors and manipulators have the environment there is a certain amount of "sense", when the mechanical arm is to use the program as a basis. Difference is that the robot begand上海电影院修缮工程 安装工程监理细则 上海电影院修缮工程项目安装工程监理细则 一、专业工程概况和特点1、、工程概况1、项目名称：上海电影院修缮工程2、工程地址：徐汇区复兴中路1186号3、建设单位：上海市徐汇区人民政府湖南路街道办事处4、监理单位：上海海龙良策工程顾问有限公司5、施工单位:上海徐房建筑实业公司6、设计单位：上海核工程研究设计院7、工程投资额：项目总投资约4483.35万元.8、计划施工工期：计划开工日期为2014年6月30日，竣工日期为2015年6月30日，计划施工工期360日历天，监理周期360日历天。

2、专业工程施工的特点2.1本工程主要是修缮和二次精装修本工程为丙级剧场2.2、强电：消防用电、备用照明、安保用电、通信用电为二级负荷配电，一般用电设备为三级，采用二级防雷措施2.3、弱电：包括火灾自动报警系统、通信系统2.4、通风与空调：通风、空调冷媒管采用铜管，凝结水采用UPVC管，空调送、回风管、通风排气管采用镀锌钢板制作2.5、给排水：给水由市政直接供给，排水采用污废分流3、监理依据3.1 本工程的设计施工图及设计文件和有关技术资料，标准图集等3.2 施工合同、监理委托合同等3.3 经批准的本工程监理规划、施工组织设计等3.4 现行国家有关法律、施工检验规范、标准、强制性要求3.5上海市建委相关的规定和文件4、监理工作流程附：1.审查施工单位的资质证书、营业执照、安全许可、项目经理、安全员证书，审批施工组织设计（方案）施工计划2.审查工程技术人员资质、数量和特殊工种证件3.检查机械设备和劳动力计划已进场情况是否满足开工要求单位工程开工申请报告承 包 人 监理工程师审 核 不全要求退回 监理工程师巡检，对存在问题，口头、备忘录、发监理通知单整改。

　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　、　　　　　　　　　　　　　　　　　　　　　　　　　　分部、分项工程施工承 包 人 　　 提供材料、成品、半成品、构配件等样品及技术资料承 包 人 　　　　　　 . 　　　　　　　　　　　　　 发监理通知单整改　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　 分部、分项、隐蔽自查承 包 人试验时旁站监理工程师 监理工程师审查/留样不符要求 　　　　　　　　　　附：1. 试验报告2. .合格证3. 质量自查记录4. 分部、分项工程验收评定报告5. 监理工程师检验回复自检合格填《报验申请表》承 包 人 　 采 购承 包 。