项目一交换机的基本配置与管理

1、 项目一 交换机的基本配置与管理一、实验目标掌握交换机基本信息的配置与管理二、技术原理交换机的管理方式基本分为两种：带内管理和带外管理。通过交换机的Console端口管理交换机属于带外管理：这种管理方式不占用交换机的网络端口，第一次配置交换机必须利用Console端口进行配置。通过远程Telnet、拨号等方式属于带内管理。三、交换机的命令行操作模式主要包括：用户模式 Switch特权模式 Switch#全局配置模式 Switch(config)#端口模式 Switch(config-if)#四、实验步骤1、实验拓扑2、交换机基本配置命令 a. 进入特权模式 Switchenable /en=enable Switch# b. 进入全局配置模式 Switch#configure terminal /conf t=configure terminal Enter configuration commands, one per line.End with CNTL/Z. c. 进入交换机端口视图模式 Switch(config)#interface fastEthernet 0/1 /int

2、 f0/1=interface fastEthernet 0/1 Switch(config-if)# d. 配置交换机端口速度 Switch(config-if)#speed ? 10 Force 10 Mbps operation 100 Force 100 Mbps operation auto Enable AUTO speed configuration Switch(config-if)#speed 100 e. 配置交换机端口双工模式 Switch(config-if)#duplex ? Switch(config-if)#duplex full f. 退回到上一级模式 Switch(config-if)#exit Switch(config)# g. 直接退回到特权模式 Switch(config-if)#end Switch# %SYS-5-CONFIG_I: Configured from console by console Switch# h. 查看交换机版本信息 Switch#show versionCisco IOS Software, C2960 Soft

3、ware (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2005 by Cisco Systems, Inc.Compiled Wed 12-Oct-05 22:05 by pt_teamROM: C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(25r)FX, RELEASE SOFTWARE (fc4)System returned to ROM by power-onCisco WS-C2960-24TT (RC32300) processor (revision C0) with 21039K bytes of memory.24 FastEthernet/IEEE 802.3 interface(s)2 Gigabit Ethernet/IEEE 802.3 interface(s)63488K bytes of flash-simulated non-volatile configuration memory.Base

4、 ethernet MAC Address : 0040.0B69.8831Motherboard assembly number : 73-9832-06Power supply part number : 341-0097-02Motherboard serial number : FOC103248MJPower supply serial number : DCA102133JAModel revision number : B0Motherboard revision number : C0Model number : WS-C2960-24TTSystem serial number : FOC1033Z1EY -More-.Configuration register is 0xF i. 查看当前生效的配置信息Switch#show running-configBuilding configuration.Current configuration : 1033 bytes!version 12.2no service timestamps log datetime ms

5、ecno service timestamps debug datetime msecno service password-encryption!hostname Switch!interface FastEthernet0/1 duplex full speed 100!interface FastEthernet0/2!interface FastEthernet0/3!interface FastEthernet0/4!interface FastEthernet0/5 -More-.!end j. 帮助信息 Switch#?Exec commands: Session number to resume clear Reset functions clock Manage the system clock configure Enter configuration mode connect Open a terminal connection copy Copy from one file to another debug Debugging functions (see al

6、so undebug) delete Delete a file dir List files on a filesystem disable Turn off privileged commands disconnect Disconnect an existing network connection enable Turn on privileged commands erase Erase a filesystem exit Exit from the EXEC logout Exit from the EXEC more Display the contents of a file no Disable debugging informations ping Send echo messages reload Halt and perform a cold restart resume Resume an active network connection setup Run the SETUP command facility -More- Switch#co?configure connect copy Switch#copy ? flash: Copy from flash: file system ftp: Copy from ftp: file system running-config Copy from current system configuration startup-config Copy from startup configuration tftp: Copy from tftp: file system

《项目一交换机的基本配置与管理》由会员人***分享，可在线阅读，更多相关《项目一交换机的基本配置与管理》请在金锄头文库上搜索。