侧弯支座冲压模具及工艺设计
42页1、精选优质文档-倾情为你奉上摘 要本次设计生产的是侧弯支座,零件外形虽然比较简单,但成形工艺复杂,包括冲裁和多次弯曲。而且精度要求比较高,形状比较复杂,生产批量大。通过工艺性分析,工序为落料、冲孔和弯曲。为了适应大批量生产的要求,采用级进模制造,能很好的解决上述问题。原料为2A12M,采用自动送料器和自动送料装置送料。模架采用四导柱四导套结构和弹性卸料板,并在卸料板和固定板之间设置辅助导向机构的小导柱和小导套,保证卸料板有足够的运动精度。关键词:侧弯支座,级进模、落料,冲孔,弯曲ABSTRACTWhat this design produces is a lateral support, the accuracy has higher request, the shape is more complicated, produce batch quantity big, pass craft analysis, work preface all for fall to anticipate with blunt bore and bending. Adopting the class en
2、ters a mold manufacturing, can be good to resolve these problems. The raw material selects the 2A12M material, the adoption sends to anticipate a machine automatically and sends to anticipate device to send to anticipate automatically.The mold adopts four lead pillar and Four sets of lead and flexibility of the bead, and be unloading to anticipate plank and fix plank of the constitution lend support to direction organization-small lead pillar with small lead a set, assurance unloads to anticipat
3、e the plank contain enough sport accuracy.Key words: lateral support ,progressive die ,fall to anticipate, blunt bore, bending目 录1 绪论-11.1 冲压加工与模具设计简介-11.2 冷冲压与模具技术国内外发展现状-21.3 选题的意义-32 工艺分析、排样设计及方案对比确定-42.1 冲裁件工艺性分析-4 2.1.1 分析工件的技术要求-5 2.1.2零件材料的选用-5 2.1.3零件的结构工艺性分析-5 2.2 冲裁工艺方案的对比与确定-6 2.2.1冲裁工序的组合-6 2.2.2冲裁顺序的安排-7 2.2.3工艺方案的比较-7 2.3 冲裁件排样设计-8 2.3.1排样方法-8 2.3.2搭边值的选用-9 2.3.3条料宽度的确定-10 2.3.4步距的确定-11 2.3.5材料利用率的确定-113 冲压力及压力中心的确定-13 3.1 冲压力的计算-13 3.2 压力中心的计算-15 3.3 压力机的选择-16 3.3.1冲压设备类型的选择-16 3.3.2确定压力机设备的规格-174 模具结构设计-18 4.1 冲裁间隙-18 4.1.1冲裁间隙的影响-18 4.1.2冲裁间隙的选用-19 4.2 模具刃口尺寸的计算-21 4.2.1计算原则-21 4.2.2计算方法-21 4.2.3各工位凸凹模刃口尺寸计算-224.3 送料方式的确定-254.4 定位方式的选择及定位装置-254.5 卸料方式的选择-254.6 模架的选择-
《侧弯支座冲压模具及工艺设计》由会员夏**分享,可在线阅读,更多相关《侧弯支座冲压模具及工艺设计》请在金锄头文库上搜索。
采区新职工培训计划
2023年市场营销部详细工作总结.docx
2023年教师个人计划总结《教育的真谛》读后感.docx
2023年护理部上半工作总结5篇范文.docx
2023年全方位开放、促进县域经济外向化的思考.docx
20XX年小学世界环境日主题班会教案.doc
《物体分类》教学设计
团体心理辅导方案与对策
2023年党组织参与重大事项决策制度.docx
承插式盘扣脚手架支模架安全技术交底
2023年客服部年终工作总结.doc
福建装修工程室内环境质量保证合同A2款
2023年明工作计划共4篇范文.docx
合法离婚协议书标准模板(十一篇).doc
2023年单片机实训心得体会.docx
工商管理认识实习报告
项目工程技术管理制度
合作协议书精选版(四篇).doc
变配电室值班制度(六篇).doc
奖励请示格式范文.docx
2023-05-24 20页
2022-11-11 5页
2022-11-29 114页
2023-10-21 106页
2023-09-18 4页
2023-07-01 11页
2023-09-12 21页
2023-02-04 2页
2022-09-12 10页
2023-09-20 7页