
日立压缩机规格书.doc
10页涡旋压缩机技术规格书Specification for Scroll Compressor Model: 403DHV-64D2Y广 州 日 立 压 缩 机 有 限 公 司编制审核 客户确认 Hitachi Compressor Products (Guangzhou) Co.,Ltd 广州日立压缩机有限公司1.规格 Specification11 压缩机 Compressor压缩机型号 Compressor Model403DHV—64D2Y压缩机型式 Compressor Type变频压缩机 Inverter Controlled Compressor压缩机方式 Compression Type涡旋式 Scroll Type使用冷媒 RefrigerantR22排气容积 Displacement64cm3/rev润滑油 / 油量 Oil / Oil ChargeSUNISO 4GDI—HT / 1800ml涂装 Painting黑色 Black Color Paint总质量(含油) Net Mass(Including Oil)37kg吸气管接口内径 Suction Accept I。
DФ22.2mm排气管接口内径 Discharge Accept I.DФ12.9mmCCC认证号 CCC Certification No.200301070409871912 电机 Motor变频器电源 Transducer Power380/415V,3~,50Hz/60Hz电动机型式 Motor Type三相感应电机3 Phase Induction Motor 运转频率范围Running Frequency Range30~90Hz频率变化Frequency Vary加速Acceleration Speed1Hz/s~3Hz/s减速Decelerate Speed0.5Hz/s工作电压范围 Voltage Range基本V/F特性+10% Basic V/F+10%绝缘等级 Insulation ClassF级 F Class绕组阻抗 Winding Resistance(at 20℃)0.86467%Ω基本V/F特性Basic V/F Characteristics 13 性能 Performance制冷能力 Capacity at 60Hz14200W输入功率 Motor Input4300W能效比 EER3.30W/W运行电流 Running Current11。
5A噪音 Sound Level≤60dB(A)振动 Vibration≤15 m/s2※ 制冷能力测试条件 Test condition of cooling capacity:冷凝温度 Condensing temp54.4 ℃ 蒸发温度 Evaporating temp7.2 ℃回气温度 Return gas temp.:183 ℃ 周围温度 Ambient temp35.0 ℃膨胀阀前液体温度 Liquid temp1℃1.4 一般特性 Characteristics 气密试验压力 Leak Tight Pressure30MPa[高压侧 H.P. Side] / 15MPa[低压侧LP. Side]耐压试验压力Hydrostatic Strength Pressure45MPa[高压侧 H Side] / 23MPa[低压侧LP. Side]绝缘阻抗 Insulation Resistance10MΩ Min.绝缘耐压 Withstand Voltage1,830V-1min.残余水分量 Residual Moisture350mg Max.含尘量 Residual Impurities100mg Max。
2 压缩机配件 Accessories Of CompressorNO名称 Parts Name数量 Qty代号 Drawing NO.备注 Remarks1支撑螺柱 Bolt4TP1—101标准部件Standard Parts2防振胶垫 Rubber Grommet B 4TP1—1023防振胶座 Rubber Grommet A 4TP1—1034垫圈 Washer 4TP1-1045M6螺母 M6 Screw Nut 4GB41—86—M66M8螺母 M8 Screw Nut 4GB41-86—M87弹性垫圈 Spring Washer 4GB93-87-68温控器挡板 Thermostat Holder 1TP1—105选择部件Option Parts9排气温控器 Discharge Thermostat 1TP1-10610热油器 Crankcase Heater 1TP1-1103. 使用条件范围 Operating Conditions蒸发温度 Evaporating Temp.—15~15℃排气温度 Discharge Temp冷凝温度+15℃)~120℃以下(Condensing Temp.+15℃)~120℃ Max。
绕组温度 Winding Temp120℃以下 Max.压缩机外壳温度 Shell Temp115℃以下 Max吸气压力 Suction Pressure0.1~0.7MPa (起动、除霜等短时间运转除外;Except the short period such as start,defrost)排气压力 Discharge Pressure1.1~2.8MPa压力比 Pressure Ratio2~75 (起动、除霜等短时间运转除外;Except the short period such as start,defrost)起动时的压力差Pressure Difference At Starting排气压力-吸气压力≤0.30MPa D.P—S.P. less than 030MPa启停周期 On/Off Period周期为10分钟以上,停止时间必须3分钟以上10 minutes min/cycle,OFF should be over 3 minutes最低油量 Minimum Oil Charge400ml Min.异常升压/降压Abnormal Press Rise/Drop上升:3.0MPa以下 Rise:3.0MPa Max。
下降:02MPa以上 Drop:02MPa Min.配管(铜管)应力Copper Piping Stress启动时:50MPa以下 Start:50MPa Max.运转时:10MPa以下 Run:10MPa Max冷媒水分含量Refrigerant Moisture Level60ppm以下 Max系统固体杂质含量Solid Impurities Level100mg以下 Max.运转倾斜角度 Tilt In Operation压缩机倾斜最大5以内 5 deg. Max.※ 其他注意事项 Remarks:1.设置排气单向阀可以起到能量调节与压缩机不带压差启动;The exhaust check valve may adjust capacity ,and startup at no pressure difference每台压缩机都需要独立设置电流、压力、温度等保护装置;Some protected device should be mounted for any compressor ,for instance current, pressure and temperature.3。
在系统匹配时需要考虑在各种运行模式如:高落差长配管、最大注氟量等情况下的回油状况,当压缩机出厂注油量(1800ml)不能够保证压缩机运行的最低油量400ml时可以从压缩机排气侧补充适量牌号为SUNISO 4GDI-HT的冷冻机油It should be given our attention to oil that compressor runs for example long tube and the max. refrigerant If compressor oil fall short of 400ml,it must be injected from the exhaust.4压缩机在去除吸、排气接头盖后,请勿放置10分钟以上;Installation shall be completed within 10 minutes after removing the caps of suction and discharge tube5.请勿压缩空气;Do not compress air.6.在真空状态下请勿通电;Do not energize under vacuumed condition。
7.在环境温度低于20℃时,必须安装油加热器(40~80W,220V);Crankcase heater is require if ambient temp is below 20℃.8.请勿反向旋转;Do not reverse rotate9.运转时,各相间的电压偏差应在额定电压的3%以内;Voltage (run):Voltage deviation each phase shall be within 3% of the rated voltage.10成箱压缩机包装件的叠放堆码极限为2箱,装卸过程中严禁翻滚;Pile limits 2 pallet.Tumbling is forbidden during handling11.向压缩机充油或冷媒时,必须从排气侧进行;Charge oil or refrigerant from the discharge pipe压缩机的接地装置应永久与制冷器具的接地装置连接;The compressor’s ground should be connected with that of refrigeration system permanently and firmly.13。
并联系统中回油毛细管前必须安装过滤器A filter is require before capillary tube in Multiple refrigerant4 附图 Attachment A—1 压缩机外形图 Dimension of Compressor A-2 压缩机性能曲线1 Compressor Performance Curve 1 A-3 压缩机性能曲线2。












