焊接工艺评定报告[PQR1-15].doc

NB/T47014-2011 焊接工艺评定报告〔PQR单位名称：Fabricator: 焊接工艺评定报告编号 PQR16-01HP 预焊接工艺规程编号 pWPS16-01HP WPS No PQR No 焊接方法 钨极氩弧焊打底/焊条电弧焊填充盖面 机械化程度〔手工、半自动、自动 手工 Welding Method Extent of mechanization 接头简图Welding Joint Sketch 母材Base Metal材料标准 GB713 W. M. Standard钢号 Q345R Steed Brand类、组别号 Fe-1-2 与类、组别号 Fe-1-2 相焊Category. Assembly No. With Category. Assembly No. Welding厚度 12mm Thickness直径 / Diameter其他 / Others 焊后热处理 PWHT温度范围〔℃ / Temperature Region保温时间〔h / Time Hold保护气体：Shielding Gas气体种类 混合比 流量〔L/minGas Categocy Mixture Flow Rate保护气 Ar 99.99 10 S G尾保气 / / / T S G 背保气 / / / B S 填充金属Filler Metal焊材标准W.M. Standard NB/T47018.3 /NB/T47018.2焊材牌号W. M. Brand ER50-6 / J506 焊材规格Welding SpecificationØ2.5/ Ø4.0 焊缝金属厚度Weld Metal Thickness 12mm 其 他Others / 电特性Electric Power电流种类Welding Current 直流〔DC 极 性Polarity 正接〔EN 反接〔EP 钨极尺寸Tungsten Electrode Size 2.5 焊接电流Welding Current 120 /160/140/140 电弧电压Arc Votage 13/26/24/24 其 他Others / 焊接位置Position Of Welding对接焊缝位置 平焊 方向〔向上、向下Position Of Butt Weld Flatness Direction角焊缝位置 / 方向〔向上、向下Position Of Fillet Weld Direction技术措施Technical measur焊接速度〔cm/min 12/16/13/13 Welding Speed摆动焊或不摆动焊 / Weave Bead Welding Or Non weave Bead Welding摆动参数 / Weave Bead Parameter单道焊或多道焊 多道焊 Single Pass Welding Or Multi-pass Welding单丝焊或多丝焊 单丝焊 Single Wire Welding Or Multi Wire Welding其 他Others / 预热Preheating预热温度<℃> 20℃<室温>Preheating T层间温度<℃> 250℃Inter pass T其 他 / Others耐蚀堆焊金属化学成分<%>Chemical Composition Of Corrosion Resistant Overlay Weld Metal<%>焊材牌号W. M. Brand C Si Mn P S Cr Ni Mo CuH10MnSi0.0870.630.990.0140.0160.0220.009/0.11 J5060.0580.450.980.0180.0090.0230.0190.010/其他Others / NB/T47014-2011 焊接工艺评定报告拉伸试验Tension Test 试验报告编号：Tension Test Report No. PQR16-01HP 试样编号Specimen No.试样宽度〔mmSpecimen Width试样厚度〔mmSpecimen Thickness横截面积〔mm2Cross Sectional Area断裂载荷〔KNFracture Load抗拉强度〔MpaTensile Strength断裂部位和特征Fracture Location And Break Performance16-01HPL1 25.112mm301.2167.47556断于母材16-01HPL2 25.112mm301.2165.66550断于母材弯曲试验Bending Test 试验报告编号:Tension Test Report No. PQR16-01HP 试样编号Specimen No.试样类型Specimen Shape试样厚度〔mmSpecimen Thickness弯心直径〔mmCenter Of Bend D.弯心直径〔°Angle Of Bend试验结果Test Result Acceptable16-01HPM1面弯10mm40180°合格16-01HPM2面弯10mm40180°合格16-01HPB1背弯10mm40180°合格16-01HPB2背弯10mm40180°合格冲击试验Impact Test 试验报告编号：Tension Test Report No. / 试样编号Specimen No试样尺寸Specimen Dimension缺口类型Notch Shape缺口位置Notch Cocation冲击温度<℃>Impact Temp冲击吸收功< J> Impact Force备注Remarks//////////////金相检验： Metallographic Examination根部:<焊透、未焊透> 焊透 焊缝: <熔合、未熔合> 熔合 Root: Weld:焊缝、热影响区：〔有裂纹、无裂纹 无裂纹 Weld、Heat Affected Zone:硬度检验Ifardness Test 试验报告编号：Tension Test Report No. / 试样编号Specimen No试样尺寸Specimen Dimension母材硬度值HBBase Metal Hardness Value焊缝硬度值HBWeld Hardness Value HB热影响区硬度值HBHAZ Hardness Value HB试验结果Test Result Acceptable////////////无损检验：N D E ExaminationRT NB/T47013.2-2015 100% II 级合格 UT / MT / PT / 其他 / 结论：本评定按 NB/T47014-2011 规定焊接试件、检验试样、测定性能、确认试验记录正确Result: This assessment has been assessed and conformed to NB/T47014-2011 standard requilements for preparation of welding specimen, performance of specimen, examina。