控制阀标准汇总.doc

控制阀标准汇总标准编号标准中文名称标准英文名称GB/T13852-1992 船用液压控制阀技术条件General specification of hydraulic control valves for shipGB/T17490-1998 液压控制阀油口、底板、控制装置和电磁铁的标识Hydraulic fluid power--Identification of valve ports,subplates,control devices and solenoidsGB/T15623.1-2003 液压传动 电调制液压控制阀 第1部分：四通方向流量控制阀试验方法Hydraulic fluid power-Electrically modulated hydraulic control valves-Part 1:Test methods for four-way directional flow control valvesGB/T15623.2-2003 液压传动 电调制液压控制阀 第2部分：三通方向流量控制阀试验方法Hydraulic fluid power-Electrically modulated hydraulic control valves-Part 2:Test methods for three-way directional flow control valvesGB/T17213.7-1998 工业过程控制阀第7部分: 控制阀数据单Industrial-process control valves Part 7: Control valve data sheetGB/T17213.8-1998 工业过程控制阀第8部分: 噪声的考虑第1节: 实验室内测量空气动力流流径控制阀产生的噪声Industrial-process control valves Part 8: Noise considerations Section 1: Laboratory measurement of noise generated by aerodynamic flow through control valvesGB/T17213.1-1998 工业过程控制阀第1部分: 控制阀术语和总则Industrial--Process control valves Part 1: Control valve terminology and general considerationsGB/T17213.5-1998 工业过程控制阀第5部分: 标志Industrial-process control valves Part 5: MarkingGB/T2514-1993 四油口板式液压方向控制阀安装面Hydraulic fluid power--Four-port directional control valves--Mounting surfacesGB/T8104-1987 流量控制阀试验方法Hydraulic fluid power--Valves--Testing method of flow control valvesGB/T7940.3-2001 气动五气口方向控制阀第三部分: 功能识别编码体系Pneumatic fluid power--Five-port directional control valves--Part 3: Code system for communication of valve functionsGB/T8106-1987 方向控制阀试验方法Hydraulic fluid power--Valves--Testing method of directional control valvesGB/T7940.2-2001 气动五气口方向控制阀第二部分带电气接头的安装面Pneumatic fluid power--Five-port directional control valves--Part 2: Mounting interface surfaces with optional elettrical connectorGB/T8105-1987 压力控制阀试验方法Hydraulic fluid power--Valves--Testing method of pressure control valvesGB/T7940.1-2001 气动五气口方向控制阀第一部分: 不带电气接头的安装面Pneumatic fluid power--Five-port directional control valves--Part 1: Mounting interface surfaces without electrical connectorGB/T8100-1987 板式联接液压压力控制阀(不包括溢流阀)顺序阀、卸荷阀、节流阀和单向阀安装面Hydraulic fluid power--Pressure control valves (excluding pressure relief valves ), sequence valves, unloading valves, throttle valves and check valves--Mounting surfacesGB/T8098-2003 液压传动带补偿的流量控制阀安装面Hydraulic fluid power--Compensated flow control valves--Mounting surfacesJB/T7387-1994(2005复审) 工业过程控制系统用电动控制阀　NF C46-520-1993 工业过程控制阀.第8部分:噪声问题.第2节:通过控制阀的液压流动产生的噪声的实验室测量(Industrial-process control valves. Part 8 : noise considerations. Section 2 : laboratory measurement of noise generated by hydrodynamic flow through control valves.)NF C46-522-1994 工业处理控制阀.第8部分:噪声条款.第4节:液压流动产生的噪声预定(EN 534-8-4)(Industrial-process control valves. Part 8 : noise considerations. Section 4 : prediction of noise generated by hydrodynamic flow.)NF E49-080-1-2002 气压液动.五通定向控制阀.第1部分:不带电连接器的安装接口(Pneumatic fluid power - Five-port directional control valves - Part 1 : mounting interfaces without electrical connector.)NF E49-080-2-2002 气压液动.五通方向控制阀.第2部分:任选电气连接器的安装接口面(Pneumatic fluid power - Five-port directional control valves - Part 2 : mounting interface surfaces with optional electrical connector.)NF C46-505-1998 绝缘过程控制阀.第2-3部分:流量容量.试验过程(Industrial-process control valves. Part 2-3 : flow capacity. Test procedures.)NF C46-630-1998 工业过程控制阀.第6部分:控制阀与定位器连接用安装细节.第1节:线性传动装置上安装的定位器(Industrial-process control valves. Part 6 : mounting details for attachment of positioners to control valves. Section 1 : positioner mounting on linear actuators.)NF E29-453-2000 工业过程控制阀门(Industrial process control valves.)标准编号标准中文名称标准英文名称NF E29-316-5-2001 供水用阀门.适用性要求和专用检查试验.第5部分:控制阀门(Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 5 : control valves.)NF C46-521-2001 工业过程控制阀.第8部分:噪声问题.第3节:气动控制阀噪声预测法(Industrial-process control valves - Part 8-3 : noise considerations - Control valves aerodynamic noise prediction method.)NF E48-435-1998 液压传动.尺寸02、03和05的四端口模式排气阀和四端口方向控制阀.夹紧尺寸(Hydraulic fluid power. Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05. Clamping dimensions.)NF C46-519-2001 工业过程控制阀.第8部分:噪声考虑.第1节:实验室测量气动流经控制阀产生的噪声(Industrial-process control valves - Part 8 : noise considerations - Section 1 : laboratory measurement of noise generated by aerodynamic flow through control valves.)NF C46-531-2001 工业过程控制阀.第6-2部分:定位器装到控制阀的安装细则.旋转传动装置上安装的定位器(Industrial-process control valves - Part 6-2 : mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators.)NF E49-091-2002 气压传动.控制阀和其它部件的孔口和控制机械的验证(Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components.)XP E29-140-1999 使用气体燃料的家用装置的控制阀.安全控制阀(带有集中自动密闭器的)(Control cocks for household appliances using ga。