巴鲁夫iol模块.pdf

BNI PBS-502-001-Z001 Profibus IO-Link Master User´s Guide 1 Inhalt 1 Notes for the user 3 1.1 About this manual 3 1.2 Structure of the manual 3 1.3 Typographical conventions 3 Enumerations 3 Actions 3 Syntax 3 Cross-references 3 1.4 Symbols 3 1.5 Abbreviations 4 2 Safety 5 2.1 Intended use 5 2.2 General safety notes 5 2.3 Meaning of the warnings 5 3 Connection overview 6 3.1 Connection overview BNI PBS-502. 6 4 Basic knowledge 7 4.1 Product describtion 7 4.2 Profibus 7 4.3 IO-Link 7 4.4 Communication mode 8 Standard IO-modes (SIO-mode) 8 4.5 Replacing modules 8 5 Technical Data 9 5.1 Dimensions 9 5.2 Mechanical data 9 5.3 Electrical data 9 5.4 IO-Link data 9 5.5 Operating conditions 9 6 Installation 10 6.1 Mechanical connection 10 6.2 Electrical connection 11 Function Ground 11 Supply voltage 12 6.3 Bus connection 13 6.4 Ports 13 I/O ports 13 IO-Link port 13 6.5 Replacing BNI PBS modules 13 7 Startup 14 7.1 Profibus address 14 Adressing 14 7.2 Configuration 14 GSD file 14 Header module 15 Structure oft he header modules 15 Header byte coding 15 Length byte coding 15 Data modules 15 Data module coding 16 Process data coding 17 7.3 Setting parameters 18 Norm-specific parameters 18 Station status 18 Balluff Network Interface Profibus, BNI PBS-502-001-Z001 2 WD_Fact_1 and WD_Fact_2 18 MinTSDR 19 Ident_Number_High 19 Ident_Number_Low 19 Group_Ident 19 User parameters 20 Configuration examples 21 Example 1 21 Example 2 22 Example 3 23 7.4 Integration in project planning software 24 Installing the GSD file 24 Requirements 25 Integration of the module 25 Define properties 26 Slot configuration 26 8 Diagnostics 27 8.1 Function indicators 27 LED indicators 27 Module LEDs 27 I/O Port LEDs 27 IO-Link Port LEDs 27 Diagnostics input 27 8.2 Diagnostics telegram 28 8.3 Norm diagnostics 28 Norm diagnostics coding 28 Status 1 28 Status 2 29 Status 3 29 Address 29 Ident_Number_High_Byte 29 Ident_Number_Low_Byte 29 8.4 Device-specific diagnostics 30 Coding of the device-specific diagnostics 30 Header 30 Status Typ 30 Slotnummer 30 Status specifier 30 Status message 1 30 Status message 2 30 8.5 Module-specific Diagnostic 31 Coding of the module-specific Diagnostic 31 Header 31 Module 31 8.6 Channel-specific diagnostics 32 Mapping of the channel-specific diagnostic 32 Header 32 Channel 32 Error 32 9 Appendix 33 9.1 Scope of delivery 33 9.2 Ordercode 33 9.3 Order information 33 9.4 ASCII table 34 10 Notes 35 3 1 Notes for the user 1.1 About this manual This Guide describes the Balluff Network Interface BNI PBS-. for use as a decentral in- and output module for connecting to a Profibus-DP network. 1.2 Structure of the manual The manual is organized so that the sections build on one another. Section 2: Basic safety information. Section 3: An overview of connection options. Section 4: Introduction to the material. Section 5: Technical data for the Profibus module. Section 6: Mechanical and electrical connection. Section 7: Logging the Profibus module on to the network. Section 8: Function indicators and the diagnostic telegram for the Profibus module. 1.3 Typographical conventions The following conventions are used in this manual: Enumerations Enumerations are shown in list form with bullet points. • Entry 1 • Entry 2 Actions Action instructions are indicated by a preceding triangle. The result of an action is indicated by an arrow.  Action instruction 1,  Action result.  Action instruction 2. Syntax Numbers: • Decimal numbers are shown without additional indicators (e.g. 123), • Hexadecimal numbers are shown with the additional indicator hex (e.g. 00hex). Menu commands: Menu commands are separated by a vertical line. “Tools | Install new GSD…“ refers to the menu command “Install new GSD….“ From the “Tools“ menu. Buttons: Buttons are shown in brackets, e.g. [Install]. Cross-references Cross-references indicate where additional information on the topic can be found (see Section 5 “Technical Data“). 1.4 Symbols Note, tip This symbol indicates general notes. Note! This symbol indicates a security notice which most be observed. Balluff Network Interface Profibus, BNI PBS-502-001-Z001 4 1 Notes for the user 1.5 Abbreviations A-Port Digital output port BCD Binary coded switch BNI Balluff Network Interface DESINA DEcentralized and Standardized INstAllation technique EMC Electromagnetic Compatibility FE Function ground GSD file Generic Station Description I-Port Digital input port I/O port Digital input or output port PB PROFIBUS PELV Protective Extra Low Voltage PLC Programmable Logic Controller Profibus-DP Profibus Decentralized Periphery S7 Programming software STEP 7 for the SIMATIC S7 controller family (Siemens AG) SELV Safety Extra Low Voltage 5 2 Safety 2.1 Intended use The BNI PBS-. serves as a decentral in- and output module for connecting to a Pr。