焊接材料质量管理规定.doc

书目Table of Contents1 范围 61 Scope 62 引用标准 62. Normative references 63 职责 83. Responsibilities 84 选购 84. Purchase 85 验收 95.1 验收项目 95.1.1 包装检验 95.1.2 质量证明书检验 95. Acceptance inspection 95.1 Inspection items 95.1.1 Packing inspection 95.1.2 Inspection of quality certificates 95.1.3 外观检验 95.1.4 成分与性能试验 105.2 检验结果的认可 105.3 验收标记 105.1.3 Exterior inspection 105.1.4 Composition and performance test 105.2 Approval of inspection results 105.3 Inspection mark 106 入库 106. Warehousing 117 库存保管 117.1 存放条件 117. Storage 117.1 Storage conditions 117.2 库存期间的检查 127.2 Inspection during storage 128 出库 128. Distribution 129 运用过程中的管理 139.1 一般要求 139. Management during use 149.1 General requirements 149.2 烘干、保温与清理 149.2 Drying, heat insulation and cleaning 149.3 识别标记 159.4 焊接材料的回收 159.3 Identification mark 159.4 Recovery of welding materials 159.5 回收的焊接材料的烘干 169.6 焊剂的重复运用 169.5 Dry of recovery welding materials 169.6 Repeated use of welding flux 16焊接材料质量管理规程Corporate Management Rules for Welding Material Quality Control1 范围本标准规定了焊接材料,包括焊条、焊丝、焊剂、合金粉末、衬垫与焊接用气体等，在选购 、验收、库存保管与运用过程中的管理要求。

为了保证焊接材料的运用性能，应具备必要的贮存、烘干、清理设施，建立牢靠的管理规程并严格执行本标准适用于焊接生产中，上述这些焊接材料的质量管理1 ScopeThis Standard specifies management requirements of welding materials (e.g., welding electrode, welding wire, welding flux, alloy powder, backing and welding gas) during purchase, acceptance, warehousing and use. In order to ensure service performance of welding materials, necessary storage, drying and cleaning installations shall be made available, and reliable management specifications shall be established and strictly observed.This Standard applies to quality management of the said welding materials during welding operation.2 引用标准下列标准所包含的条文，通过在本标准中引用而构成为本标准的条文。

标准出版时，所示版本均为有效全部标准都会被修订，运用本标准的各方应探讨运用下列标准最新版本的可能性GB/T5117-1995 《碳钢焊条》 GB/T5118-1995 《低合金焊条》 GB/T983-1995 《不锈钢焊条》 GB/T984-2001 《堆焊焊条》 2. Normative referencesThe following standards contain provisions which, through reference in this Standard, constitute provisions of this Standard.At time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below.GB/T5117-1995 Carbon steel electrodesGB/T5118-1995 Low alloy steel electrodesGB/T983-1995 Stainless steel covered electrodesGB/T984-2001 Hardfacing electrodes for shielded metal arc weldingGB/T 13814—92 《镍与镍合金焊条》GB/T 15620—1995 《镍与镍合金焊丝》GB/T14957-1994 《熔化焊用钢丝》 GB/T8110-1995 《气体爱护电弧焊用碳钢、低合金钢焊丝》 GB/T10045-2001 《碳钢药芯焊丝》 GB/T17493-1998 《低合金钢药芯焊丝》 GB 4242—85 《焊接用不锈钢丝》GB/T5293-1999 《埋弧焊用碳钢焊丝和焊剂》 GB/T 13814—92 Nickel and nickel alloy covered welding electrodesGB/T 15620—1995 Nickel and nickel alloy wires for welding rodsGB/T14957-1994 Steel wires for melt weldingGB/T8110-1995 Welding electrodes and rods for gas shielding arc welding of carbon and low alloy steelGB/T10045-2001 Carbon steel flux cored electrodes for arc weldingGB/T17493-1998 Low alloy steel flux cored electrodes for arc weldingGB 4242—85 Stainless steel wires for weldingGB/T5293-1999 Carbon steel electrodes and fluxes for submerged arc weldingGB/T12470-2003 《低合金钢埋弧焊用焊剂》 GB10433-2002 《电弧螺柱焊用园柱头焊钉》 GB/T4842-2006 《纯氩》 GB/T6052-1993 《工业用二氧化碳》 HG/T2537-1993 《焊接用二氧化碳》 CCS 规范 材料焊接部分DNV 规范 材料焊接部分ABS 规范 材料焊接部分GL 规范 材料焊接部分BV 规范 材料焊接部分LR 规范 材料焊接部分GB/T12470-2003 Low-alloy steel electrodes and fluxes for submerged arc weldingGB10433-2002 Cheese head studs for arc stud weldingGB/T4842-2006 Pure argonGB/T6052-1993 Commercial liquid carbon dioxideHG/T2537-1993 Carbon dioxide for welding purposeCCS - Rules for materials and weldingDNV -Rules for materials and weldingABS - Rules for materials and weldingGL - Rules for materials and weldingBV - Rules for materials and weldingLR - Rules for materials and welding3 职责3.1 设计部依据各项目的特点和要求制定材料打算单。

3.2 物资部依据材料打算单负责选购 相关事宜，并且负责材料的入库保管和出库3.3 质管部负责来料验收和现场的运用监督3.4 各生产运用部门负责焊材的领用、保管和发放回收事宜3.5 对业主规定有特别要求的项目，要依据业主的规定要求修订具体项目的管理规定，并监督执行 3. Responsibilities3.1 Design Department shall make a material requisition based on the features and requirements of each project.3.2 Procurement Department is responsible for making purchases according to the material requisition and for warehousing materials and sending materials out of warehouse.3.3 Quality Management Department is responsible for incoming inspection and supervision over field use.3.4 Each production department is responsible for the requisition, custody, distribution and recovery of welding materials.3.5 For each project specially required by the Owner, the management rules for the project shall be made according to the Own。