（一）模具专业基本用词.doc

一） 模具专业基本用词1 塑料:plastic, resin 样件：sample 注塑机:injection, machine, press 产品：part, product, moulding2、 模具：mold, mould, toolA简易模（样板模）：prototype mold B量产用模具：production mold3、 三维造型（数模）：moedl.,3D data 二维产品图：2D part drawing4、 制造：manufacture, build, construction 检验：check‘inspection 测量： measure Jnspection5x 修改：change ,modify, correction T程更改：engineer change6、质量：quality 数星：quantity 基准：datum, reference（二） 如何解析 2D 产品图？ How to read 2D part drawing?1、 点:point 线:line ,edge 面:face A 侧面:side B 表面:surface C 外观面:appearance surface2、 壁厚:wall thickness, stock thickness 加强筋（骨位）:rib 孔位:hole 槽:slot3、 角：corner A 圆角：fillet B 倒角：chamfer C 尖角：sharp corner4、 斜度：angle taper（三）分模信息Splitting分型线:parting line （P/L）,splitting line 主分模方向:main direction, line of draw浇口设定:gating（四） 产品标识 Part Identification产品名称：part name（P./N） 产品编号+版木号：number + revision（Rev.） 型腔号:cavity number 材料标记：material symbol 模具编号：mold number（NO.） 日期印:dating insert, date code 循环印:cycling code 公司标志:company logo（五） 技术要求 Specification（Special Requirement）1 x 项目启动表:Kick-off sheet项 目 名称：part name, product name, part description 产品编号：part number （P/N） 客八模号：customer mold no.项目启动日期:kick off date, start date 项目完成日期:due date, lead time内模件用钢：tool steel型腔数量：number of cavities数模文件编号：data file no.2、 注塑材料:resin, plastic, raw material 收缩率：shrink, shrinkage, shrink factor 注塑机吨位:molding machine size, injection machine size 成型周期:cycle time 型腔（型芯）表面粗糙度:cavity polish （core polish）皮纹:texture, grain 拔模斜度：draft angle, removal taper 注數件顔色及光泽：molded color & gloss模具加丁地：manufacturing facility 热流道供应商：manifold manufacturer, manifold supplier 浇口 类羽：gate type 浇口 位置：gate location/position 产品 标识：stamp information, part identification 特殊要求：special instructions3、 产品质量及外观要求part quality & appearance尺寸及公禺 dimension & tolerance 重要尺寸：critical dimension, important dim., key dim. 理论尺寸：nominal dimension 实际尺寸:actual dimension 公差（带）:tolerance （range） 尺寸超差:dimension deviation 接受（合格）:accept, OK 拒绝（不合格）：reject, refuse,obsolete, NG 让步接受：concession, special admit 返工：re-work4、 产品缺陷:defects缩印：sink mark, shrinkage 飞边：flash, burr 段并：mismatch 银丝纹：snake marks, streak 弯曲：warpage 打不足（缺料）：short shot熔接线：weld line5、 产品夕卜观 part appearance产品顔色：part color产品光泽：gloss皮纹粒度：grain6、 常用词汇、词组及短语normal work, short sentence单边：per side双边：both side加入，添加：add, incorporate未注尺寸见三维造型：non dimensioned contour（detailed shape）see 3D model. 分型线上的飞边（披缝）或段羌小于：buirs and discrepancy on the P/L shall be or less（六） 制模标准模具结构术语：mold construction terminology模架：mold base 模厚：stack height of mould 模具重量：total weight of mould, mould thickness 定模底板：front plate, top clamping plate, clamp plate, clamping plate 定模板：cavity plate, fixed mould plate, A-plate 动模板：core plate, moving mould plate, B-plate 支撑板：support blocks, rails, risers, spacer block 顶杆固定板:retaining plate, ejector retaining plate 顶板：ejector plate 动模底板：back plate 导柱：guide pillar, leader pin, guide pin 导套：guide bush, leader pin bush 复位杆：return pin, push-back pin 弹簧：spring 撑头：support pillar 推板导柱、导套：ejection guide pin/bush 扌当钉：stop pin, stop button 站立脚：standing-off pillars 标牌：plaque（七） 成型零部件 moulding components型芯：core 型腔:cavity 镶针：core pin 镶块:insert, split 滑块:slide, sliding split 斜顶：lifter, angled-lift split 斜顶杆：lifer rod, lifter shaft 成型顶杆：moulding face pin, form pin（八） 浇注系统feed system主流道：sprue分流道runner主分流道：main runner次分流道：branch runner分流道截面 形状：cross-section shape of runner 圆形:full round 半圆形:semicircular 改形的梯形: modified trapezoidal 边浇口 （J 形浇口）: edge gate, J-gate 侧浇口: side gate 潜伏式浇口: sub-gate, cashew gate, subsurface gate, submarine gate 潜"IH弋二次（隧道工弋）：tunnel gate onto feeder post 点浇口： pin gate 直接浇口: sprue gate, direct gate 护耳式浇口: tab gate 模腔：impression 冷料井：cold slug well 热流道：hot runner定位圈：locating ring, register ring 浇口套:sprue bush 挡圈:stop ring 浇口镶块：gate insert 热流道板：manifold热嘴：hot drop（九） 分型面及其锁紧、排气 parting surface, inter-locking & venting分型线：parting line 镶拼线:bodyline,joint line 平/不平的分型面:flat/non flat parting surface 封胶面：shut off surfaces 擦位：shutoffs 碰穿位：kiss-off 管位：parting line lock 分型血的習放（避空）：relief of parting surface 分型面的平衡：balancing of parting surface 锁紧角度:locking angle 锁模板:safety strap 精定位:interlock, die lock 困气：air trap 排气槽:vent, vent slot（十）滑块机构slide驱动：actuation 余I■导柱：angle pin, horn pin, cam pin, 弹簧：spring 汕缸：hydraulic cylinder 制动：detention 滑块固泄器：slide retainer 弹簧制动器：spring-lotided detention（plunger） 挡钉、扌当板：stop pin, stop plate, slide stop 导轨:gib, guide strip 锁紧块：heel block, locking heel, wedge block, chase block 咐磨片：wear plate, wear strip 压板:retainer 螺钉:screw 定位销：dowel（H^一）斜顶机构lifer斜顶头:lifter head 斜顶杆：lifter rod, lifer shaft 开 I I销:split pin 固定板（压板）：retainer plate 耐磨片：wear plate 铜导套：bronze bushing 衬套：spacer 导轨：gib 滑动块：slide（十二）顶出系统 ejection system基本词汇:basic word顶出行程:ejection stroke模具开档:daylight粘模：stick 产品脱模：part is push off from, clear part of mould, separation of part 顶板机构 ejector plate assembly 顶板（推板）：ejector plate 顶板固定板:retaining plate 推板Ml 定板：ejector guide pin 推板导套：ejector guide bush 撑头：support pillar, pillar。