聚氨酯工程机械面漆的组成和使用.doc

聚氨酯工程机械面漆的组成和使用Intended Uses用途聚氨酯工程机械面漆适用于各种工程机械的的涂装用面漆，如建筑机械，农用机械、矿山机械、桥梁机械、交通设施等，也适用各种气候条件下户外钢结构的长效防腐面漆As finish, suitable to paint all kinds of engineering machinery, such as architectural machine, agricultural machine, mining machine, bridge machine and means of transportation etc. Also may provide long-term anticorrosive protection for outdoor steel structure in all kinds of climate.ProductDescription产品简介高性能丙烯酸聚氨酯面漆，双灌装，以羟基丙烯酸树脂，耐候颜料及脂肪族异氰酸酯二聚体等制成，漆面美观，具有优良的抗磨损性能，优异的耐紫外线性能，优异的保色保光性能，不易粉化，不易泛黄，高硬度和附着力强，抗轻度化学物质，低温下亦能快速固化，高光、半光或哑光。

Two-pack paint, based on Hydroxy acrylic resin, weathering pigment and aliphatic Isocyanate dimmer, etc. Excellent performance, Good appearance. The paint film possesses excellent wearability, resistance to ultraviolet, color and gloss retention(no chalking or yellowing), and strong adhesion, In addition, it is hard and resistant to weak chemicals, Fast dry even at low temperature, High gloss, half gloss or matt.Volume Solids 固体份 About 55% 约 55% Dry Film Thickness 干膜厚度 30-50microns 30-50 微米Theoretical Coverage 理论涂布率11.5m2 /Kg based on iron red polyurethane intermediate paint film thick 50um 11.5 平方米/公斤(以深色漆和 50 微米干膜厚计)ProductInformation产品数据Practical Coverage 实际涂布率 Allow appropriate loss 允许适量损耗Mix Radio 混合比 A：B=6 : 1 (WT) 甲：乙=6 ：1（WT）Application Details施工详述Method of Application 施工方法 Airless Spray 无空气喷涂 Recommended 推荐采用Brush or Roller 涂刷或辊涂 Suitable, but using short fur roller to decrease bubble适用，但需使用短毛滚筒以减少起泡产生Conventional Spray 传统喷涂 Recommended 推荐采用Air assistant –Airless Spray Recommended 推荐采用Thinner 稀释剂 C004Cleaner 油漆设备清洗剂 C004Pot Life 使用期 5 ℃：6 h 23 ℃：4 h 35 ℃：2 hStorage 贮存期 A: One year 甲: 一年 B:6 months 乙：6个月Over coating Interval覆涂间隔SubstrateTemperature底材温度,℃Touch Dry 表干,hHard Dry硬干,hMix 最短 Max 最长 Drying time 干燥时间52335≤2≤1≤0.5≤48≤36≤2416 h8 h4 h5 d3 d1 dStorage 贮存 dry and cool conditions, far from fire and heat source贮存于阴凉干燥处,远离火源、热源 A:18Kg in 20 liter container 甲： 18 公斤装于 20 公升容器中Pack size 包装规格 B:3Kg in 4 liter container 乙：3 公斤装于 4 公升容器中Flash Point 闪点 Above≥23℃ (Basic agent, curing agent or mixture)大于 23℃（主剂固化剂、混合物）Storage andHandling贮存与管理Specific Gravity 比重 1.20-1.30Kg/L 1.20-1.30 公斤/ 公升 Specification and Surface preparation技术要求及表面处理Used for the surface over primer or intermediate-coating, and the surface must be clean, dry and no oil or dirty. 来自 Preceding cost: Epoxy ester, epoxy and polyurethane primer or intermediate paint.聚氨酯工程机械面漆用于涂装已涂底漆或中涂漆的表面，需保持表面清洁、干燥、无油污。

前道配套涂料：环氧酯类、环氧类、聚氨脂类底漆或中涂漆LimitationsMust mix component A and B according to the appropriate necessary quantity. Recommended making this paint just before painting, Should use up in pot life in case it would cure and could not be used.限制In storage or application, should avoid water vapor.按规定比例现配现用，在使用期内用完储藏及涂装时，应避免接触水气SafetyPrecautions安全措施The product must be used in painting area by professionals. When painting, please be sure to refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying the product.The product is a kind of solvent-based paint. In order to avoid the accident or dangerous occurrence, minimal safety precaution, as follow, should be down.The paint contains volatile solvent and it is flammable, So must keep away from sparks and open flames. No smoking at workplace, Effective precautions (such as using explosion-proof electrical equipments. No static electricity accumulation or metal collision etc) also should be done so as to avoid product sparks. Enough ventilation is necessary at application sites. In order to remove any danger of explosion, must keep the ratio of gas / air is less than 10 %, Usually 200 m3of ventilation quantity per 1 Kg solvent (according to the solvent) is necessary, it canMaintain the minimum explosive limit. Take effective precautions to prevent skin and eye contact with the coating (such as the use of overalls, gloves, goggles, face shields and protective oil coating and so on). If paint gets in touch with skin,If accidental skin contact with the product, please use fresh water and soap or an appropriate industrial cleaning agents thoroughly cleansed. In case of eyes being contaminated, rinse with fresh water for 10 min at least and give medical treatment immediately.During painting, it is recommended to wear face shields to prevent inhalation of paint mist and harmful gases.Especially in poorly ventilated environment, it is more necessary.Finally, be handled with care so as。