连接器群组测试报告-connector-test-report.doc

. DESCRIPTION：产品说明H3.75 CONNECTOR高度3.75mm连接器PART NO.：料号1233-3321152DATE：日期2012/12/28DOCUMENT NO.：文件QA-2012122804REV.：版本ABY APPROVED核准BY CHECKED审核WRITTEN制作INDEX索引1. SCOPE 3适用围2. APPLICABLE DOCUMENTS 3适用的文件3. TEST CONDITIONS AND SEQUENCE 3 ~ 5测试条件与次序4. TEST METHOD OF INSPECTION 5 ~10测试检验方法5. SUMMARY OF THE QUALIFICATION 11 ~ 27 TEST RESULT测试结果 6. APPENDIX 28附件1. SCOPE适用围1.1 TESTED SAMPLES: 85 pcs.测试样品数: 85个1.2 PURPOSEThis qualification test report contains the quality requirements, test procedures and test results of a qualification test program on the part no:101001-510510目的这个合格检验报告针对泰强料号: 101001-510510进行测试，测试容包含合格测验规、测验程序和测验的结果2. APPLICABLE DOCUMENTS适用的文件2.1 EIA-RS-3642.2 Test report of FCN: QA-20121228043. TEST CONDITIONS AND SEQUENCE测试条件与次序3.1 TEST CONDITIONSUnless otherwise specified, tests and examinations were conducted under conditions within the following ranges:Temperature: 20±5℃Atmospheric Pressure: 650 to 800 millimeters (25.6 to 31.5 inches) of MercuryRelative Humidity: 40% to 70%测试条件除非额外规定,检验依下面的围之的条件下实施：温度: 20 ± 5 ℃大气压力：650至800毫米( 25.6至31.5英吋) 水银柱高。

相对湿度：40%到70%3.2 QUALIFICATION TEST SEQUENCE测试次序Item项目DESCRIPTION表达SEQUENCE 次序METHOD方法ABCDEFGHIJKLMNOPQ1Examination of product外观检验1，31，411，41，51，91，91，91，91，91，51，51，51，31，3114-12Contact resistance接触阻抗2，42，82，82，82，82，82，42，42，44-23Insulation resistance绝缘阻抗3，63，63，63，63，64-34Dielectric withstanding Voltage 耐电压4，74，74，74，74，74-45TEMPERATURE RISING 温升24-56Vibration振动24-67Mechanical shock机械冲击34-78Contact retention force保持力24-89Mating force插入力24-910Unmating force拔出力34-911Durability耐插拔34-1012Thermal shock热冲击54-1113Humidity热湿性测试54-1214Humidity-temperature cycling温湿度循环54-1315Temperature life高温寿命54-1416Low temperature低温寿命54-1517Salt spray盐水喷雾34-1618H2S Gas硫化氢测试34-1719Ammonia(NH3)Gas氨气测试34-1820Solderability沾锡性24-1921Soldering heat withstanding 耐焊锡性24-2022Lock Strength锁卡强度24-2123Reverse mating force反向插入力24-224. TEST METHOD OF INSPECTION测试检验方法4-1 EXAMINATION OF PRODUCTVisual inspection and dimensional examination in compliance with applicable specifications and documents were performed. The test samples shall be free from defects such as damage, creep, deformation, blister and burrs that are detrimental to the functions and appearances of test samples.外观检验目视检查和尺寸的检验依照已实施之规与文件做其检验容。

测验样品不应有影响功能性与外观不良等缺陷，如损害、潜变、变形、水泡和毛边等问题4-2 CONTACT RESISTANCEThe test was performed in accordance with EIA-364-23. Open circuit voltage is 20 mV maximum and test current is 100 mA maximum level contact resistance requirement is 40 mΩ (resistance of termination wires shall be deducted from the reading) for initial samples, I.e., samples have not been subjected to any environmental test, and is 80 mΩ for environmentally stressed samples..接触阻抗此测试依据EIA-364-23.来执行检测测试电压是20 mV最大值并且测验电流是100 mA最大值初始样品最大接触阻抗为40 mΩ (线材的阻抗值应从所得到的电阻值中扣除)样品经过环境的测试最大接触阻抗为80 mΩ。

4-3 INSULATION RESISTANCEInsulation resistance was measured between adjacent contacts after applying 500 VDC for 1 minute. The test was performed in accordance with EIA-364-21. Minimum insulation resistance requirement is 100 MΩ for initial samples.绝缘阻抗绝缘阻抗为相接连之端子经由500 VDC通过一分钟后，所量测之值此测试依据EIA-364-21来执行检测样品未受任何环境测验，最小绝缘体阻抗需求对于初始样品为100 MΩ4-4 DIELECTRIC WITHSTANDING VOLTAGEA 500 VAC was applied between two adjacent contacts of the test samples for 1 minute. While applying the voltage, the leakage current was monitored and shall be less than 0.5 mA. The test was performed in accordance with EIA-364-20.耐电压相接连之端子经由一 500 VAC流电通过一分钟。

在通过电压时,漏电电流应小于0.5 mA此测试依据EIA-364-20.来执行检测4-5 TEMPERATURE RISINGContact series-wired, apply test current of loaded rating current t。