簇优化参数20130411.xls

加扰参数 用于下行虚拟加扰dlInterferenceEnable Enable Downlink Interference generationdlInterferenceLevel Interference level for generated download interferenceactPdcchLoadGen Activate PDCCH load generationpdcchLoadLevel PDCCH load level传输模式切换门限tm3to7CqiTh CQI threshold for switch from TM3 to TM7 tm7to3CqiTh CQI threshold for switch from TM7 to TM3mimoOlCqiThU CQI threshold for activation of OL MIMO SMmimoOlCqiThD CQI threshold for fallback to MIMO diversity下行传输模式设置dlMimoMode Downlink MIMO ModeactTmSwitch Active transmission mode switch功率修改 多用于覆盖调整pMax Maximum output powertxPowerScaling TX power scalingdlCellPwrRed Cell power reducedlRsBoost Downlink reference signals transmission power boost邻区添加adjEnbId Identity of neighbor eNB within PLMNcPlaneIpAddr C-Plane IP address of neighbor eNB定时器t300 Timer T300t310 Timer T310t311 Timer T311t301 Timer T301t304IntraLte Timer T304 intra-LTEt304InterRAT Timer T304 for interRAT切换参数enableBetterCellHo Enable better cell HOa3offset A3 offseta3ReportInterval A3 report intervala3TimeToTrigger A3 time to triggerenableCovHo Enable coverage HOthreshold3 Threshold th3 for RSRPthreshold3a Threshold th3a for RSRPa5ReportInterval A5 report intervala5TimeToTrigger A5 time to triggeractIfHo Enable interFrequency handoverthreshold2InterFreq Threshold th2 interFreq for RSRPthreshold2a Threshold th2a for RSRPcellIndOffServ Cell individual offset of own serving cells PCIcellIndOffNeigh Cell individual offset of neighbour cellsoffsetFreqIntra Intra EUTRA offset frequencyoffsetFreqInter Inter EUTRA offset frequency规划相关参数phyCellId Physical layer cell identitygrpAssigPUSCH Group assignment for PUSCH工程参数设置ppsTimingOffset Air Frame Timing As For 1PPS Reference  30m o dS C Hgrp A s s igP U P C Iu原始值 修改值false true0 50false true0 5080 根据优化适度修改130 根据优化适度修改120 根据优化适度修改90 根据优化适度修改Dynamic Open Loop MIMOSingleTX/TXDiv/ Dynamic OpenLoop MIMO/Closed LoopMimo/Single StreamBeamforming/Dual StreamBeamformingtrue false40.0 40.0/37.04024 根据优化适度修改0 根据优化适度修改0 30～ 1048575 根据规划添加根据规划添加200ms 根据优化适度修改200ms 根据优化适度修改3000ms 根据优化适度修改200ms 根据优化适度修改500ms 根据优化适度修改500ms 根据优化适度修改true true6 根据优化适度修改240ms 根据优化适度修改40ms 根据优化适度修改true true50 根据优化适度修改54 根据优化适度修改240ms 根据优化适度修改40ms 根据优化适度修改enabled 根据组网需求更改51 根据需求更改89 根据需求更改0dB 根据不同小区个性化设置0dB 根据不同小区个性化设置0dB 根据异频组网策略设置0dB 根据异频组网策略设置0～ 503 根据规划修改0～ 29 根据规划修改0 us 根据需求修改含义下行 PDSCH虚拟加扰开关下行干扰加载水平下行 PDCCH虚拟加扰开关PDCCH加载水平CQI_TM3->7CQI_TM7->3TM3单流向双流切换 CQI门限TM3双流向单流切换 CQI门限Cell specific downlink transmission/mimo mode当下行传输模式为 TM3或 TM7时，若 actTmSwitch为 true，则传输模式为自适应，否则为固定 TM3或 TM7TM3/TM7自适应开关小区单 PATH发射功率， 10W=40dBmDefines the mapping of the RP3 I and Q values amplitude into theTX power on the cell小区功率（ dBm） =pMax- dlCellPwrRed/10 -20lg（ 4024/txPowerScaling）Sets the power reduction from the antenna maximum TX power.取值范围 0～ 10dB， internal_value = gui_value * 10例如设置为 100，表示下行发射功率降低 10dB， RSRP会相应降低10dB取值 0、 1.77、 3、 4.77、 6dBUE侧定时器， T300用于 Msg3超时当 UE传输 RRCConnectionRequest，启动 T300；上层接收RRCConnectionSetup或 RRCConnectionReject 信息，小区重选以及连接建立失败，停止 T300当检测物理层问题，比如收到来自低层的 N310次连续不同步指示，启动 T310； 当收到来自低层的 N311次连续同步指示、触发相应的切换过程以及初始化连接重建立过程，停止 T310； 若定时器超时，如果安全没有被激活，回到 RRC_IDLE 状态，否则初始化连接重建立过程当初始化 RRC连接重建立过程，启动 T311；当选择一个合适的 E-UTRA或 otherRAT小区，停止 T311；当定时器超时，进入RL25具备 SON功能，只需添加基站 IP及 eNB识别号，基站根据位置信息 /UE上报 MR等来自动添加邻区关系，添加邻区后系统会在 LNCEL下生成邻区关系0dB 263989 3 allowedautomatic当传输 RRCConnectionReestabilshmentRequest时，开启 T301；当接收 RRCConnectionReestablishment或RRCConnectionReestablishmentReject消息，也包括选择的小区变得不合适的情况，停止该定时器；当定时器超时，进入 RRC_IDLE状Flag if better cell HO is enabled.Handover margin for better cell HO.internal_value = gui_value * 2Defines the interval with which measurement reports are sent aslong as the specific criteria for the measurement event A3 are met.Time for which the specific criteria for the measurement event A3must be met in order to trigger a measurement report.Flag if coverage HO is enabled.A5切换服务小区门限A5切换邻小区门限Defines the interval with which measurement reports are sent aslong as the specific criteria for the measurement event A5 are met.Time for which the specific criteria for the measurement event A5must be met in order to trigger a measurement report.异频切换开启Threshold for RSRP of serving cell. If value below Th2_InterFreqthan inter frequency measurements are startedThreshold for RSRP of serving cell. If Inter-RAT measurements areactive and the value exceeds Th2a, inter-RAT measurements arestopped. Th2 < Th2a.Physical layer cell identity parameter defines a cell uniquely.当 PCI调换时 grpAssigPUSCH需同时调换The parameter defines assigned PUSCH group.Different systems could have difference in the frame synchronisationto GPS PPS timing pulse. This parameter gives possiblity to adjustfreely an air interface timing as for 1PPS synchronisation pulse.取值 -4900～ 4900us， internal_value = gui_value * 10此参数设置需全网相同，否则会出现站间同步问题A3/A5切换中小区个性化偏置，详见 3GPP 36.331 cellIndividualOffsetA3/A5切换中频率偏置，详见 3GPP 36.331 offsetFreqUE侧定时器， T304用于切换超时当 UE接收 RRCConnectionReconfiguration 信息，包括Mobili。