冰淇淋机英文说明书.pdf

Table of Content1.SPECIFICATION 1 2.MACHINE OVERVIEW 2 3.PREPAIRING 3 Power source requirement 3 Prepairing 3 Safety 3 4.INSTALLATION 4 Install the beater 4 Install the dispenser door 4 Install the drip tray and rear seal drip pan 5 Install the air pumps 5 5.OPERATION 7 Refrigeration 7 Standby 7 Pre-cooling 8 Cleanout 8 Mix low alert 8 6.ADVANCED OPERATION 10 Parameter adjusting 10 Motor current display 10 Restore factory setting 10 7.MAINTENANCE 11 Wash the machine 11 Wash it step by step 11 Troubleshooting Bacterial Count 12 Regular Maintenance Checks 12 8.ICE CREAM RAW MATERIALS 14 9.TROUBLESHOOTING GUIDE 1522. MACHINE OVERVIEWhopperrear seal drip pandisplay & keypadsdispenser doordrip pan3Power source requirement• Power source MUST match the specification.• This machine MUST be properly grounded! Failure to do so can result in severe personal injury from electrical shock.• The machine MUST NOT share wire or power jack with other appliances.• We recommend using wires thicker than 4mm2. Small wire may cause damage to motor and compressor.• DO NOT operate the machine with fuse larger than specification, and DO NOT power on before trouble removed.• We DO NOT take responsible for damage caused by unqualified power source or wire.Prepairing• Please reset the machine more than 12 hours before producing if the machine is moved from one place to another.• Minimum clearance of 20cm is requried around the machine. The clearance should be extended to 50cm when machines are working together.Safety• Only trained personnel should operate the machine.• Power source MUST be disconnected before repairing or maintenance.• Please confirm all the stainless steel panel and dispenser door are fixed before power on.• DO NOT operate the machine unless all service panels and access doors are restrained with screws.• DO NOT put any objects or fingers into spout doors or cylinder.3.PREPAIRING4plastic handlestainless steelhandlescrewstainless steel plungerscrewplastic plungerO-ringsealdesign cover4.INSTALLATIONInstall the beaterThe beaters are depend on models1. Assemble the beater with seal at the bottom, and lubricate both ends of the beater2. Put the beaters into the cylinder, and make sure that the hexagonal end is put into the hole of axis guide of reducer.Install the dispenser door51. Put O-rings on the plastic plungers with lubricant(the middle plunger should be paired with O-O-ring).2. Install the plungers into the holes of the dispenser.3. Fix the stainless steel plunger with the stainless steel handle through the holes on dispenser door and screw tight.4. Fix the design cover on the bottom of the dispenser.5. Fix the dispenser door assembly on the machine and fasten it with screws using the spanner. Please DO NOT lubricate the seal of the dispenser door6. Fix the plastic handles onto the stainless onesInstall the drip tray and rear seal drip panPlease refer to section MACHINE OVERVIEWInstall the air pumps(optional, machines with air pumps)pump shellgearsealpump coverattaching bolts screwconnect tubeO-ringO-ringrubber plugspring O-ringsucking tubeO-ring61. Put the initiative and driven gear into the air pump shell.2. Put seal on the air pump cover, cover with the shell and screw with attaching bolts.3. Install rubber plug, spring, O-ring and sucking tube on the bottom of the air pump sequently.4. Install two O-rings on the back of the air pump and one O-ring at the front.5. Install O-ring on the connect bolt, and assemble the bolt inside the hole in the front of the air pump.6. Install O-ring on the tube, and connect the two connect bolts with the tube.Rotate the handle on sucking tube to adjust overrun. (From top view), clockwise for more and counterclockwise for less. Handle on the left is biggest and on the right is smallest.Note• The two air pumps are exchangeable integrally, but DO NOT exchange any parts inside the pumps with one another.• There MUST be no impurities in the mixture, failure to do this may damage the pumps. It is recommend to filter and cleansing the material before using.• If the pump does not work on powering on, take off the connect tube and inject a little liquid into the pump to help its starting.75.OPERATIONThe machine state is , when it connects to power source.RefrigerationWhen the machine is in state, press key, it will start to refrigerate and the state will turn to be .When temperature reaches preset value, the ice-cream state will turn to be , refrigeration will be stopped and ice cream is ready. You may make ice cream by pull down the handle.After making several cones of ice cream or 300 seconds after stop refrigerating, the machine will restart to refrigerate. We do suggest users not to make ice cream when the ice cream state is .When the machine is in state, press key to stop refrigerating.In the state, are unavailable, while are available.StandbyStandby mode maintains the mixture fresh in the hopper as well as ice cr。