连接器群组测试报告connector test report.docx

H3.75 CONNECTOR高度3.75mm连接器2012/12/28DESCRIPTION：产品说明PART NO.： 料号DATE： 日期DOCUMENT NO.： 文件号码 REV.：版本BY APPROVED 核准BY CHECKED 审核WRITTEN 制作INDEX索引1. SCOPE3适用范围2. APPLICABLE DOCUMENTS 3适用的文件3・ TEST CONDITIONS AND SEQUENCE 3 ? 5测试条件与次序4・ TEST METHOD OF INSPECTION 5?10测试检验方法5・ SUMMARYOFTHEQUALIFICATION 11?27TEST RESULT测试结果6・ APPENDIX28附件1・ SCOPE适用范围1・1 TESTED SAMPLES: 85 pcs・测试样品数: 85个1・2 PURPOSEThis qualification test report contains the quality requirements, test procedures and test results of a qualification test program on the part no:101001-510510目的这个合格检验报告针对泰强料号: 101001-510510进行测 试，测试内容包含合格测验规范、测验程序和测验的结果2・ APPLICABLE DOCUMENTS适用的文件2.1 EIA-RS-3642.2 Test report of FCN:3. TEST CONDITIONS AND SEQUENCE测试条件与次序3.1 TEST CONDITIONSUnless otherwise specified, tests and examinations were conducted under conditions within the following ranges:Tempera tu re: 20±5CAtmospheric Pressure: 650 to 800 millimeters (25.6 to 31.5 inches) of MercuryRelative Humidity: 40% to 70% 测试条件 除非额外规定,检验依下面的范围之内的条件下实施： 温度：20 ± 5 C大气压力：650至800毫米( 25.6至31.5英寸) 水银柱高 相对湿度：40%到70%3.2 QUALIFICATION TEST SEQUENCE测试次序DESCRIPTION 叙述SEQUENCE 次序ABCDEFGHIJKLMNOPQ1Examination of product外观检验1，31，411，41，51，91，91，91，91，91，51，51，51，31，3114-12Contact resistance 接触阻抗2，42，82，82，82，82，82，42，42，44-23Insulation resistance 绝缘阻抗3，63，63，63，63，64-34Dielectric withstanding Voltage耐电压4，74，74，74，74，74-45TEMPERATURE RISING 温升24-56Vibration 振动24-67Mechanical shock 机 械冲击34-78Contact retention force保持力24-89Mating forc e插入力24-910Unmating force 拔出力34-911Durability 耐插拔34-1012Thermal shock 热冲击54-1113Humidity 热湿性测试54-1214Humiditytemperature cycling 温湿度循环54-1315Temperature life 高温寿命54-1416Low temperature 低温寿命54-1517Salt spray 盐7水喷雾34-1618HS Gas 硫化氢测试34-1719Ammonia(NH)Gas3氨气测试34-1820Solderability 沾锡性24-1921Soldering heat withstanding 耐焊锡性24-2022Lock Strength 锁卡强度24-2123Reverse mating force反向插入力24-224. TEST METHOD OF INSPECTION测试检验方法4-1 EXAMINATION OF PRODUCTVisual inspection and dimensional examination in compliance with applicable specifications and documents were performed. The test samples shall be free from defects such as damage, creep, deformation, blister and burrs that are detrimental to the functions and appearances of test samples.外观检验 目视检查和尺寸的检验依照已实施之规范及文件做其检验内容。

测 验样品不应有影响功能性及外观不良等缺陷，如损害、潜变、变形 水泡和毛边等问题4-2 CONTACT RESISTANCEThe test was performed in accordance with EIA-364-23. Open circuit voltage is 20 mV maximum and test current is 100 mA maximum level contact resistance requirement is 40 mQ (resistance of termination wires shall be deducted from the reading) for initial samples, I.e., samples have not been subjected to any environmental test, and is 80 mQ for environmentally stressed samples..接触阻抗此测试依据EIA-364-23.来执行检测测试电压是20 mV最大值并 且测验电流是100 mA最大值初始样品最大接触阻抗为40 mQ (线 材的阻抗值应从所得到的电阻值中扣除)样品经过环境的测试最大 接触阻抗为 80mQ。

4-3 INSULATION RESISTANCEInsulation resistance was measured between adjacent contacts after applying 500 VDC for 1 minute. The test was performed in accordance with EIA-364-21. Minimum insulation resistance requirement is 100 MQ for initial samples.绝缘阻抗绝缘阻抗为相接连之端子经由500 VDC通过一分钟后，所量测之 值此测试依据 EIA-364-21 来执行检测样品未受任何环境测验， 最小绝缘体阻抗需求对于初始样品为 100 MQ4-4 DIELECTRIC WITHSTANDING VOLTAGEA 500 VAC was applied between two adjacent contacts of the test samples for 1 minute. While applying the voltage, the leakage current was monitored and shall be less than 0.5 mA. The test was performed in accordance with EIA-364-20.耐电压 相接连之端子经由一 500 VAC 流电通过一分钟。

在通过电压时, 漏电电流应小于0.5 mA此测试依据EIA-364-20.来执行检测4-5 TEMPERATURE RISINGContact series-wired, apply test current of loaded rating current to the circuit, and measure the temperature rising by probing on soldered area of contacts. After the temperature becomes stabilized deduct ambient temperature from the measured value.温升连续接触连线，适用对电路测试装载电流，通过在接触的焊接区域 量测所提升温度，当温度变的稳定以后，从测量的温度数值。