EN6033529A13和EK1的解释课件.ppt

1 / 11 -6Sigma是我们的工作方式是我们的工作方式1微波电器部门：部门： 研究院测试认证中心研究院测试认证中心时间：时间：20112011年年0707月月3030日日EN60335-2-9:A13:2010+EK1 解释解释微波电器事业部微波电器事业部- 2 / 11 -6Sigma是我们的工作方式是我们的工作方式2微波电器EN60335-2-9/A13:20101) EN 60335-2-9/A13:2010 Part 2-9: Particular requirements for grills, toasters and similar portable cooking appliance发布期 DOP: 2011-10-01强制实施期 DOW: 2013-10-012) EK1AG2 （以下简称EK1)Guidance for Implementation of CENELEC Guide 29 – Test and Certification Decisions 发布期 DOP: 2011-07-01强制实施期 DOW: 2011-10-01凡需要获得GS证书必须满足EK1的要求！- 3 / 11 -6Sigma是我们的工作方式是我们的工作方式3微波电器EN60335-2-9/A13:2010涉及小于18Kg的桌面微波炉，带烧烤功能一、结构更改1）后背电源线插孔：原因：8.1.1 Test probe B and probe 18 of EN 61032 are applied without appreciable force, the appliance being in every possible position except that appliances normally used on the floor and having a mass exceeding 40 kg are not tilted. Through openings, the test probe is applied to any depth that the probe will permit and is rotated or angled before, during and after insertion to any position. If the opening does not allow the entry of the probe, the force on the probe in the straight position is increased to 20 N when probe B is used or 10 N when probe 18 is used. If the probe then enters the opening, the test is repeated with the probe in the angled position. However when using test probe 18 the appliance shall be fully assembled as in normal operation without any parts removed; parts that are intended to be removed for user maintenance shall not be removed.使用测试指18的时候,期间在正常操作情况下测试. 任何可拆卸部件都不拆卸- 4 / 11 -6Sigma是我们的工作方式是我们的工作方式4微波电器EN60335-2-9/A13:2010防危险运动部分的新的测试方法:20.2Replace the first paragraph of compliance by: Compliance is checked by inspection, by the tests of 21.1 and by means of: – a test probe that is similar to test probe B of IEC 61032 but having a circular stop face with a diameter of 50 mm, instead of the non circular face, applied with a force of 5 N and – test probe 18 of IEC 61032, applied with a force of 2,5 N. - 5 / 11 -6Sigma是我们的工作方式是我们的工作方式5微波电器Probe 18Department name9/11/2024EN60335-2-9/A13:2010- 6 / 11 -6Sigma是我们的工作方式是我们的工作方式6微波电器EN60335-2-9/A13:2010孔径为孔径为10mm，，Probe 18的可以插进去，的可以插进去，碰到运动的扇叶或高压电容的带电部分碰到运动的扇叶或高压电容的带电部分- 7 / 11 -6Sigma是我们的工作方式是我们的工作方式7微波电器EN60335-2-9/A13:2010一、结构更改2）门玻璃、顶部，左侧，右侧，后背：原因：11.Z101 Ovens, rotary grills, rotisseries and cookers are supplied at rated power and operated under normal operation. All heating units that can be connected to the supply mains at the same time during normal use are switched on. Ovens are operated without accessories.测试方法：额定功率测试烧烤温升, Ovens are operated with the door closed. Ovens having a thermostat are adjusted to its high setting.温升考核点：所有可以被Probe41,ProbeA(EK1)接触的表面Temperature rises are not measured on the following surfaces- 8 / 11 -6Sigma是我们的工作方式是我们的工作方式8微波电器EN60335-2-9/A13:20101) surfaces on the oven door within 10 mm from the edge of the door (Zone 1);2) surfaces around the oven door within 10 mm from the left right or lower edge of the door, or25 mm from the upper edge of the door (Zone 2); 3) surfaces within 25 mm of vents (Zone 3); EK1仅豁免：Only the ventilation openings on the front side are exempted from the evaluation (ventilation of the muffle, zone 3(refer to picture Z102)). 其他：The temperature rise around all other ventilation openings has to comply with the requirements of touchable surfaces (table Z.101). 4） underside surfaces that are not accessible with test probe 41, probe A(EK1) of EN 61032，5) the rear surface of appliances which, according to the instructions, shall be placed against a wall; and are not accessible with test probe 41,probe A(EK1) of EN 61032，- 9 / 11 -6Sigma是我们的工作方式是我们的工作方式9微波电器EN60335-2-9/A13:2010- 10 / 11 -6Sigma是我们的工作方式是我们的工作方式10微波电器EN60335-2-9/A13:2010Probe 41:- 11 / 11 -6Sigma是我们的工作方式是我们的工作方式11微波电器EN60335-2-9/A13:2010Probe A:- 12 / 11 -6Sigma是我们的工作方式是我们的工作方式12微波电器EN60335-2-9/A13:2010限值的对比:surfaceEN 60335-2-9/A12EN 60335-2-9/A13Top surfaces and door surfacesOther surfacesSurface likely to be touchedBare metal856045Coated metal956555Glass and ceramic956560Plastic and plastic>0,3mm1058065请注意Note b!- 13 / 11 -6Sigma是我们的工作方式是我们的工作方式13微波电器EN60335-2-9/A13:201025mm豁免豁免10mm豁免豁免10mm豁免豁免Bare metal: 45KPlastic:65KGlass:60KBare metal: 45K(EK1:无通风口无通风口25mm豁免说法豁免说法)- 14 / 11 -6Sigma是我们的工作方式是我们的工作方式14微波电器EN60335-2-9/A13:201010mm豁免豁免10mm豁免豁免25mm豁免豁免Coated metal55KCoated metal55K判断为判断为Coated metal前提是：前提是：Metal is considered coated when a coating having a minimum Thickness of 80um made by enamel or non substantially Plastic coating is used.- 15 / 11 -6Sigma是我们的工作方式是我们的工作方式15微波电器EN60335-2-9/A13:201010mm豁免豁免10mm豁免豁免25mm豁免豁免Coated metal55KCoated metal55K判断为判断为Coated metal前提是：前提是：Metal is considered coated when a coating having a minimum Thickness of 80um made by enamel or non substantially Plastic coating is used.- 16 / 11 -6Sigma是我们的工作方式是我们的工作方式16微波电器EN60335-2-9/A13:2010Coated metal55KBare metal45K在说明书有“the rear surface of appliances shall be placed against a wall”下炉子底板部位，炉子底板部位，若碰到则为若碰到则为Coated metal55KBare metal45KEK1:判断为判断为Coated metal前提是：前提是：Metal is considered coated when a coating having a minimum Thickness of 80um made by enamel or non substantially Plastic coating is used.- 17 / 11 -6Sigma是我们的工作方式是我们的工作方式17微波电器EN60335-2-9/A13:2010一、结构更改3）器具的器具的start/stopstart/stop开关需要给用户提供视觉和听觉或者触觉的反馈开关需要给用户提供视觉和听觉或者触觉的反馈：原因：7.10 Addition:Devices used to start/stop operational functions of the appliance, if any, shall be distinguished fromother manual devices by means of shape, or size, or surface texture, or position, etc. A tactile or anaudible and visual feedback shall give an indication that the device has been operated.- 18 / 11 -6Sigma是我们的工作方式是我们的工作方式18微波电器EN60335-2-9/A13:2010机械式不满足要求，机械式不满足要求，定时器形状必须与调节开关不一样，定时器形状必须与调节开关不一样，必须有叮的声音必须有叮的声音电子式不满足要求，电子式不满足要求，Start/off的形状、的形状、按键声音能否按键声音能否与其他按键不一样？与其他按键不一样？正常工作正常工作的时候灯的时候灯亮亮- 19 / 11 -6Sigma是我们的工作方式是我们的工作方式19微波电器EN60335-2-9/A13:2010二、说明书增加：增加： the rear surface of appliances shall be placed against a wall- 20 / 11 -6Sigma是我们的工作方式是我们的工作方式20微波电器EN60335-2-9/A13:2010注意：- 21 / 11 -6Sigma是我们的工作方式是我们的工作方式21微波电器EN60335-2-9/A13:2010 END。