华硕外观检验规范.doc

VISUAL INSPECTIONSTANDARDEPSON DIRECT CORPORATION ENGINEERING DIVISIONRev.DateApprovalCon firmatio nPla nnerTotal sheets1.02000/1/31Y.AidoF.Hara8 Sheets1.12003/5/26F.HaraA.I kegami8 Sheets2.02006/4/11A.I kegami8 Sheets3.02006/12/8T.HirasawaT.Ya nagisawaA.I kegami12 SheetsEPSONDIRECTVISUAL INSPECTION STANDARDSHEETREVISION3.0NEXT3SHEET2Rev . statusRev.Rev. contentsRev. reas on1.0New establishme nt1.1ReviseClearer expla nati on2.0ReviseChan ged sta ndard3.0ReviseChan ged sta ndardSHEETSSTATUSSheet Rev.Sheet Rev.COVER 3.01 3.02 3.03 3.04 3.05 3.06 3.07 3.08 3.09 3.010 3.011 3.012 3.0EPSONDIRECTVISUAL INSPECTION STANDARDSHEETREVISION3.0NEXT4SHEET31.1.1To set up the visualinspectionmethod and criteria for OQC 制 订 出 货 检 查 方 式 及 等1.2To ensureoutgoingquality can meet customer 's demand 确 定 出 货 品 质 能 满 足 客 户 要求Scope 范 围Thisdocumentappliesall productwhich incoming to EPSONDIRECTandoutgoingto end-user此文件适用所有到艾谱生及到终端客户的产品1.1Completeproduct 成 品1.2Incompleteproduct(Case unit)半成品1.3Components（may follow vendor 's standard） 部件（可追踪供应商的标准）Definition详情3.1Inspectingenvironment检验环境Objectives级2.3.luminance 光 源 ； 大 约 800 流 明3.1.13.1.23.1.3度， 其他级面90度3.1.4 CategoryLighting resource: above 800 Distance: 30cm 距 离 30cmAngle: 90-45 degree(Class-1),90degree(Lessthan Class-1) 角 度 ： 1 级 面 90-453.2Time: 5sec(Class-1), 3sec(Less of defect 缺 点 分 类thanClass-1)时间：1级面5s ,其他3s前面3.2.1Criticaldefect:Defects that cause harmful or threatening forhuman body对人体有害的and theirproperty3.2.2Majordefect:Defect thatleads to function fail 主 缺： 不能达到 预期功能3.2.3Minordefect:Defect thatcause lower customer 'ssatisfaction减低客户满Definitionof surface level 表面等级描述3.3.1Class-1Notetype Topof LCD back cover andLCD frontbezel 1 级LCD 背 面 上 部 及 LCD 前 框Topof Top coverFrontof LCD back cover andLCD frontbezelFrontof Top coverLCDDesktop type Frontbezel 台 式 ： 前 框DisplayLCDand front of LCD bezel显示器：LCD和LCD面框3.3.2Class-2Notetype Left/Right side of LCD back cover and LCDfront bezel严重缺点；笔记本型笔记本型LCD 背面 及前框 左右 边意度3.3Left/RightFrontBezelDesktop type TopSideofofBottom面)DisplayCD 面 框左右 边及后 面3.3.3 Class-33级面： 笔记本型Note type3.3.4 Class-4side Bottom ODDofTop cover caseand Bottomcaseof ofCase 台 式 ： 机 箱 顶 部 Case 机箱侧 面 of Case (paintingTop ofLCD bezel 显 示 器 ：surface)机箱下面（指烤漆LCD 面 框 上 面 ，底 座 前 面 ， LLeft/Rightside ofLCDbezelandBack coverBacksideofLCDbackcoverandLCD frontBacksideofTopcoverandBottomcaseTopof Bottomcase (includingbattery)Insideofdevices(ODD)bezelFront of the Bottom basetype Back Back Left/Right Note type Inside of Desktop type Inside ofDesktopDisplayof Casecover and bottom of LCD bezel and Back side of Bottom base CaseCaseBottom of Case (metal surface)DisplayBottom of Bottom baseClass-1Fro ntbezelClass-2Top of CaseSideof CaseBottomof CaseEPSONDIRECTVISUAL INSPECTION STANDARDSHEETREVISION3.0NEXT5SHEET4Desk top type PC (TowerPC & BookPC) *Bottom case of BookPC is considered as Side caseClass-3BackofCaseBack of CaseBottom of Case (pa in ti ng surface )/(no painting)Class-4In side of CaseBottom of Case (no painting)TopTopFro ntFro ntLCDof LCD back cover and LCD front bezel of Top coverof LCD back cover andof Top coverLCD front bezelTop of LCD front bezelLCDTop of top coverFront of LCD back cover Front of LCD front bezelTop of LCD back coverEPSONDIRECTVISUAL INSPECTION STANDARDSHEETREVISION3.0NEXT6SHEET5Note Book type PCClass-1Front of top coverClass-2Left/Rightsideof LCDbackcover and LCD front bezelLeft/Rightsideof Topcoverand BottomcaseFront ofBottomcaseBezel of ODDClass-3Back side of LCD back cover and LCD front bezelBack side of Top cover and Bottom caseTop of Bottom case (including battery)Back side of。