台达DVP-14SS2说明书.docx

1. POWER, RUN, ERROR indicator8 Nameplate2. RUN/STOP switch9. Extension port3. I/O port for program communication (RS-232)10. DIN rail mounting slot (35mm)4. DIN rail clip11. Extension unit clip5. I/O terminals12. RS-485 communication port6. I/O point indicator13. Mounting rail for extension module7. Mounting hole for extension module14. DC power input[Figure 1 ]Unit: mm■ Electrical SpecificationsModalItemDVP14SS211RDVP14SS211T DVP12SS211SPower supply voltage24VDC (-15%-20%)(with counter-connection protection on the polarity of DC input power) DVPPS01(PS02): input 100-240VAC, output 24VDC/1A(PS02: 2A)Inrush currentMax 7.5A@24VDCFuse capacity1.85A/30VDC, PolyswitchPower consumption1.8W1.5WPower protectionWith counter-connection protection on the polarity of DC input powerInsulation resistance> 5MQ (all I/O point-to-ground: 500VDC)Noise immunityESD (IEC 61131-2, IEC 61000-4-2): SkVAir DischargeEFT(IEC 61131-2, IEC 610004-4): Power Line: 2kV, Digital I/O: 1kV,Analog & Communication I/O: 1kVRS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m-1 -ItemModelDVP14SS211RDVP14SS211T DVP12SS211SGroundingThe diameter of grounding wire cannol be smaller than the wire diameter of terminals L and N (All DVF units should be grounded directly to the ground pole).Operation / storageOperation: 0℃ ~ 55℃ (temp ), 50 ~ 95% (humidity), Pollution degree2 Storage: -25℃ ~ 70℃ (temp.j, 5 ~ 95% (humidity)Vibration / shock resistanceInternational standards: IEC61131-2, IEC 68-2-6 (TESTFc)/IEC61131-2 & IEC 6&2-27 (TEST Ea)Weight (g)97g 82,5g | 90gSpecIterrsInput Point24VDC (-15% ~ 20%) single common port inputInput No.X0~X3X4~X7Input typ«DC (SINK or SOURCF)Input Current (± 10%}24VDC. 5mAInput impedanceMax frequency4.7kQ20kHz | 10kHzAction levelOff-On> 15VDCOn-* Off<5VDCResponse timeOff-On< 10ps< 202On—Off< 20Ps< 50psFilter timeAdjustable within 0 ~ 20ms by D1020 (Default: 10ms)SpecOutput PointItemsRelayTransistorOutput No.Y0~Y5Y0~Y3Y4, Y5Max frequency1Hz10kHz1kHzWorking voltage250VAC, < 30VDC5 - 30VDC 和Resistive1.5A/1 point (5A/COM)0.5A/1 point (3A/COM)Max loadInductive松15W (30VDC)Lamp20WDC/100WAC2.5W (30VDC) _ResponseOff-OnApprox. 10ms20ps100pstimeOn-* Off30Ps100ps#1: UR ZP must work with external auxiliary power su叩ly 24VDC (-15% ~ *20%), ratedconsumption approx. 10mA/point#2: Life curves(oLXcomo[Figure 2]■ I/O ConfigurationModelInputOutputPointTypePointType14SS211R8DC(Sink Or Source)6Relay14SS211TTransistor (NPN)12ss211s4Transistor (PNP)I/O ConfigurationT ransistor T ransistor(NPN) (PNP)S/SX0X1X2X3X4X5X6X7UPZP・DAPWMYO”Y2Y3Note: The layout of output terminals on DVP-SS2 is different from that on DVP・SS.• Dimension & InstallationPlease install the PLC in an enclosure with sufficient space around it to allow heat dissipation, See [Figure 3].[Figure 3 ]• Direct Mounting: Use M4 screw according to the dimension of the product.• DIN Rail Mounting: When mounting the PLC to 35mm DIN rail, be sure to use the retaining clip to stop any side-to-side movement of the PLC and reduce the chance of wires being loose. The retaining clip is at the bottom of the PLC. To secure the PLC to DIN rail, pull down the clip, place it onto the rail and gently push it up. To remove the PLC, pull the retaining clip down with a 财 screwdriver and gently remove the PLC from DIn rail.■ Wiring22-16AWG< 1 5mmUse 22-16AWG (1.5mm) single or multiple core wire on I/O wiring terminals. See the figure in the right hand side for its specification. PLC terminal screws should be tightened to 1.90 kg-cm (1.65 in-lbs) and please use only 60/75℃ copper conductor.1. DO NOT wire empty terminal. DO NOT place the I/O sgnal cable in the same wiring circuit.2. DO NOT drop tiny metallic conductor into the PLC while screwing and wiring. Tear off the sticker on the heat dissipation hole for preventing alien substances from dropping in to ensure nor^l heat dissipation of the PLC.♦ Power SupplyThe power input of DVP-SS2 is DC. When operating DVP-SS2, please note the following points:1. The power is connected to two terminals, 24VDC anc OV, and the range of power is 20.4 ~ 28.8VDC. If the power voltage is less than 20.4VDC, the PLC will stop running, all outputs will go “Off, and the ERROR indicator will start to blink continuously.2. The power shutdown for less than 10ms will not affect the operation of the PLC. However, the shutdown time that is too long or the drop of power voltage will stop the operation of the PLC, and all outputs will go off. When the power returns to normal status, the PLC will automatically resume the operation. (Please take care of the latched auxiliary relays and registers inside 。