DSLJ型电热式胶带硫化器.doc

DSLJ型电热式胶带硫化器MODEL DSLJ ELECTROTHERMICRUBBER BELT VULCANIZER使用说明书OPERATING INSTRUCTION MANUAL一、硫化机的用途 Usage of VulcanizerDSLJ型电热式胶带硫化机（下称硫化机），体积小、重量轻，普通三相电源供电，热板温度均匀，水压系统供给（0～1.8MPa）均匀压力，配有轻型全自动电控箱电控箱与主机的连接由一体化插件及多芯电缆完成，操作方便、工作可靠目前广泛应用于冶金、矿山、电厂、港口、建材、化工等周围无爆炸性气体和足以腐蚀金属的有害性气体场合的帆布、尼龙、钢绳芯运输胶带的现场硫化胶接亦适用于防腐、耐热等特殊性能胶带的硫化接头胶带接头的质量，直接影响到胶带的工作效力、使用寿命，尤其是目前长距离，高强度运输带更为重要故DSLJ型电热式胶带硫化机是目前胶带运输机械中不可少的辅助设备Model DSLJ Electrothermic Rubber Belt Vulcanizer (following is called "vulcanizer'' for short), has the specialities of small volume, light weight, general three-phase power supply, homogeneous temperature of electrothemic plae. Well-distributed pressure {0-1.8Mpa) supplied by a hydiaulic system, equipping of light automatic control panel, connection of the control panel and the main equipment done by the integrated plug with the multicore cable, easy maintenance, realible working etc.It is now used widely for the on-site vulcanizing connection of canvas~ nylon, conveyer with steel cable core inside as well as for the connection of rubber belt with special characteristics of anticorrosion and heat resistant under the circumstance of no explosive gas or any harmful gas to corrode the metal~ which is accepted by the metallurgical engineering, mineral production, power station~ harbor machinery architectural working or chemical industry etc.The quality of the belt connection will influence the working efficiency of the rubber belt or the length of life directly~ especially for the long distance and high-strength conveyer. Therefore, model DSLJ vulcanizer is the necessary accessories for the rubber belt conveyer equipment.二、 技术参数 Technical Data1、硫化压力：1.5MPa， 1. Pressure of vul: 1.5MPa2、硫化温度：145℃， 2. Temp. of vul: 145℃3、硫化板表面温差：±3℃， 3. Supface temp. diff. of vul.Plate: ±3℃4、升温时间（常温到145℃）：4.Hyperthermic time: ≯50min≯50min， （mormal temp. is up to 145℃）5、电源电压：380V、50Hz， 5.Voltage: 380V、50Hz6、电控箱输出功率：36KW， 6.Output power of control panel: 36KW7、温度调节范围：0～200℃，7.Temp.～adjusting scope:0～200℃8、计时调节范围：0～59 min，8. Time.～adjusting scope: 0～59 min9、上下加热板加压0.8 MPa后9.After pressuring the up and down beating其缝隙：≯0.5㎜。

Plates in 0.8 MPa, the gap between the Piate is no more than 0.5㎜ 型号Model硫化带宽(㎜)Width of Vulcanized Belt (㎜)规格Spexification热板尺寸Size of heating plate(长×宽)（L×W）mm功率PowerKW外形尺寸Dinemsion长×宽×高(L×W×H)mm重量Weight㎏DSLJ-650650650×830830×78010.441332×830×580450650×10001000×78012.601394×1000×580567DSLJ-800800800×830830×95013.921592×830×580515800×10001000×95016.801654×1000×580645DSLJ-100010001000×830830×113015.661722×830×5806721000×10001000×113018.901784×1000×580756DSLJ-120012001200×830830×135019.141977×830×7258841200×10001000×135023.102039×1000×7251100DSLJ-140014001400×830830×155022.622242×830×7259571400×10001000×155027.302304×1000×7251185DSLJ-160016001600×830830×173024.362372×830×89513671600×10001000×173029.402434×1000×8951690DSLJ-180018001800×830830×195027.842647×830×89514801800×10001000×195033.602709×1000×8951825DSLJ-200020002000×830830×215031.322922×830×89516602000×10001000×215037.802984×1000×8952042DSLJ--220022002200×830830×233033.063052×830×89518492200×10001000×233039.902830×1000×8952273三、主要结构简介 Brief Introduction of Main Structure硫化机有主机（1、机架，2、夹紧装置，3、垫铁，4、螺杆，5、螺母，6、垫圈，9、隔热板，10、上加热板，14、下加热板，15、水压板），7、高压软管，8、试压泵，11、二次电缆，12、电控箱，13、一次电缆组成。

详见图1The vulcanizer is constituted by the following parts. l. machine frame. 2.clamps. 3.back-up iron plates. 4.bolt. 5.nuts. 6.washes. 9.heat-proof plates. 10.up heating plates.14.down heating plates.15.hydraulic plates (the above parts are the constitution of main equipment). 7.high-pressure soft pipe. 8.pressure-testing pump. 11. secondary cables. 12.controi panel. 13.prima-y cable. (please find fig. 1 in detail}图1四、硫化机的使用安装 Installation & Use of vulcanizer硫化机构件轻巧，一般人工均能搬动，安装前要考虑到电源的方便，操作空间，在运输机上施工时，用枕木搭一个平台，其要求根据硫化胶带的位置，硫化机同时使用的台数而定，施工前请准备好处理胶带的工具、胶料、0～200℃水银温度计等备件。

The structural parts of vulcanizer are light and handy, which can be carried manually. The operation space and the convenience of use of power should be considered before installaion. When putting a construction on the conveyer, a platform should be first put on by sleepers, which the dimension is according to the position of the belt to be vulcanized and the numbers of vulcanizer to be used at the same time. The other accessories such as the special tools to treat the rubber belt, the colloidal materials and the mercurial thermometer of 0℃-200℃ should be prepared as well.硫化机的安装按下列步骤进行：1、将下机架与胶带纵向成70°角摆放在平台上。

图2The procedure of the vulcanizer-in-stalling is as follows:1 .Put the d。