离心风机英文文献

Centrifugal fanA centrifugal fan (also squirrel-cage fan, as it looks like a hamster wheel) is a mechanical device for moving air or gases. It has a fan wheel composed of a number of fan blades, or ribs, mounted around a hub. As shown in Figure 1, the hub turns on a driveshaft that passes through the fan housing. The gas enters from the side of the fan wheel, turns 90 degrees and accelerates due to centrifugal force as it flows over the fan blades and exits the fan housing.1 Figure 1Centrifugal fans can generate pressure rises in the gas stream. Accordingly, they are well-suited for industrial processes and air pollution control systems. They are also common in central heating/cooling systems.1. Fan componentsThe major components of a typical centrifugal fan include the fan wheel, fan housing, drive mechanism, and inlet and/or outlet dampers.2. Types of drive mechanismsThe fan drive determines the speed of the fan wheel (impeller) and the extent to which this speed can be varied. There are three basic types of fan drives.12.1Direct driveThe fan wheel can be linked directly to the shaft of an electric motor. This means that the fan wheel speed is identical to the motor's rotational speed. With this type of fan drive mechanism, the fan speed cannot be varied unless the motor speed is adjustable.2.2.1 Belt drive Figure 2: Centrifugal fan with a belt driveBelt driven fans use multiple belts that rotate in a set of sheaves mounted on the motor shaft and the fan wheel shaft.This type of drive mechanism is depicted in figure 2. The belts transmit the mechanical energy from the motor to the fan.The fan wheel speed depends upon the ratio of the diameter of the motor sheave to the diameter of the fan wheel sheave and can be obtained from this equation:1 where: rpmfan= fan wheel speed, revolutions per minuterpmmotor= motor nameplate speed, revolutions per minuteDmotor= diameter of the motor sheaveDfan= diameter of the fan wheel sheaveFan wheel speeds in belt-driven fans are fixed unless the belts slip. Belt slippage can reduce the fan wheel speed several hundred revolutions per minute (rpm).2.2Variable driveVariable drive fans use hydraulic or magnetic couplings (between the fan wheel shaft and the motor shaft) that allow control of the fan wheel speed independent of the motor speed. The fan speed controls are often integrated into automated systems to maintain the desired fan wheel speed.1An alternate method of varying the fan speed is by use of an electronic variable-speed drive which controls the speed of the motor driving the fan. This offers better overall energy efficiency at reduced speeds than mechanical couplings.2.3 Fan dampersFan dampers are used to control gas flow into and out of the centrifugal fan. They may be installed on the inlet side or on the outlet side of the fan, or both. Dampers on the outlet side impose a flow resistance that is used to control gas flow. Dampers on the inlet side are designed to control gas flow and to change how the gas enters the fan wheel.Inlet dampers reduce fan energy usage due to their ability to affect the airflow pattern into the fan.13. Backward-curved bladesBackward-curved blades, as in Figure 3(b), use blades that curve against the direction of the fan wheel's rotation. The backward curvature mimics that of an airfoil cross section and provides good operating efficiency with relatively economical construction techniques. These types of fan wheels are used in fans designed to handle gas streams with low to moderate particulate loadings. They can be easily fitted with wear protection but certain blade curvatures can be prone to solids build-up.Backward curved fans can have a high range of specific speeds but are most often used for medium specific speed applications- high pressure, medium flow applications.Backward-curved fans are much more energy efficient than radial blade fans and so, for high horsepower applications may be a suitable alternative to the lower cost radial bladed fan.4. Straight radial bladesRadial fan blades, as in Figure 3(c), extend straight out from the hub. A radial blade fan wheel is often used on particulate-laden gas streams because it is the least sensitive to solids build-up on the blades, but it is often characterized by greater noise output. High speeds, low volumes, and high pressures are common with radial fans, and are often used in vacuum cleaners, pneumatic material conveying systems, and similar processes. Figure 35. Centrifugal fan ratingsRatings found in centrifugal fan performance tables and curves are based on standard air SCFM. Fan manufacturers define standard air as clean, dry air with a density of 0.075 pounds mass per cubic foot (1.2kg/m³), with the barometric pressure at sea level of 29.92 inches of mercury (101.325kPa) and a temperature