多场景小间距LED接收卡诺瓦科技MRV410规格参数文档英文版

Receiving Card MRV410 Receiving Card Document Number: NS110100479 Copyright © 2018 Xian NovaStar Tech Co., Ltd. All Rights Reserved. No part of this document may be copied, reproduced, extracted or transmitted in any form or by any means without the prior written consent of Xian NovaStar Tech Co., Ltd. Trademark Specifications Change History Specifications Contents www.novastar-led.cn i Receiving Card MRV410 Specifications 1 Safety1 Safety This chapter illustrates safety of the MRV410 receiving card to ensure the products storage, transport, installation and use safety. Safety instructions are applicable to all personnel who contact or use the product. First of all, pay attention to following points. l Read through the instructions. l Retain all instructions. l Comply with all instructions. Storage and Transport Safety l Pay attention to dust and water prevention. l Avoid long-term direct sunlight. l Do not place the product at a position near fire and heat. l Do not place the product in an area containing explosive materials. l Do not place the product in a strong electromagnetic environment. l Place the product at a stable position to prevent damage or personal injury caused by dropping. l Save the packing box and materials which will come in handy if you ever have to store and ship the product. For maximum protection during storage and shipping, repack the product as it was originally packed at the factory. Installation and Use Safety l Only trained professionals may install the product. l Plugging and unplugging operations are prohibited when the power is on. l Ensure safe grounding of the product. l Always wear a wrist band and insulating gloves. l Do not place the product in an area having frequent or strong shake. l Perform dust removing regularly. l Contact NovaStar for maintenance at any time, rather than have the product disassembled and maintained by non-professionals without authorization. l Replace faulty parts only with the spare parts supplied by NovaStar. 2 Overview3 Featureswww.novastar-led.cn 1 Receiving Card MRV410 Specifications 4 Hardware Structure 4.2 Dimensions The board thickness is not greater than 2.0 mm, and the total thickness (board thickness + thickness of components on front and rear panels) is not greater than 17.5 mm. The unit of dimension chart is “mm”. The location holes are connected to signal JH1 JH2 1 A1 B4 2 1 A2 B2 2 3 OE1 LAT1 4 3 OE2 LAT2 4 5 DCLK1 VCC 6 5 DCLK2 VCC 6 7 C1 D1 8 7 C2 D2 8 9 R1A G1 10 9 R5A G5 10 11 R1B B1 12 11 R5B B5 12 13 GND R2A 14 13 GND R6A 14 15 G2 R2B 16 15 G6 R6B 17 B2 R3A 18 17 B6 18 19 G3 GND 20 19 GND 20 21 R3B B3 22 21 B7 22 23 R4A G4 24 23 R8A G8 24 25 R4B B4 26 25 R8B B8 26 JH3 JH4 1 A3 B3 2 1 A4 B4 2 3 OE3 LAT3 3 OE4 LAT4 4 5 DCLK3 VCC 6 5 DCLK4 VCC 6 7 C3 8 7 C4 D4 8 9 R9A G9 10 9 R13A G13 10 R9B B9 12 11 R13B B13 12 13 GND R10A 14 13 GND R14A 14 15 G10 R10B 16 15 G14 R14B 16 17 B10 R11A 18 17 B14 R15A 18 19 G11 GND 20 19 G15 GND 20 21 R11B B11 22 21 R15B B15 22 23 R11A G12 24 23 R16A G16 24 25 R12B B12 26 25 R16B B16 26 On 16-group RGBR' parallel data output mode, the MRV410 supports 1/32 scan, where the E signal is located at R4B, R8B, R12B, and R16B. For 1/8 scan or below, Pin8 outputs control signals automatically. 20-Group RGB Parallel Data Output Mode 5 DCLK3 VCC 6 5 DCLK4 VCC 6 7 C3 D3 8 7 C4 D4 8 9 E3 R11 10 9 E4 R16 10 11 G11 B11 12 11 G16 B16 12 13 GND R12 14 13 GND R17 14 15 G12 B12 16 15 G17 B17 16 17 R13 G13 18 17 R18 G18 18 19 B13 GND 20 19 B18 GND 20 21 R14 G14 22 21 R19 22 23 B14 R15 24 23 B19 R20 24 25 G15 B15 26 25 G20 B20 26 JH1 JH2 1 A1 B1 2 1 A2 B2 2 3 OE1 LAT1 4 3 OE2 LAT2 4 5 DCLK1 VCC 6 5 DCLK2 VCC 6 7 R1 G1 8 7 R7 G7 8 9 B1 R2 10 9 B7 R8 10 11 G2 B2 12 11 G8 B8 12 13 GND R3 14 13 GND R9 14 15 G3 B3 16 15 G9 B9 16 17 R4 G4 18 17 R10 G10 18 19 B4 GND 20 19 B10 GND 20 21 R5 G5 22 21 R11 G11 22 23 B5 R6 24 23 B11 R12 24 25 G6 B6 26 25 G12 B12 JH3 JH4 1 A3 B3 2 1 A4 B4 2 3 OE3 LAT3 4 3 LAT4 4 5