办公室全套表格大全[推荐]
HBLGXL01XX公司签呈呈报部门: 年 月 日呈报:抄报:份 数抄送:页/份主旨:事由: 呈报人: 日期: 年 月 日上一级领导批示:年 月 日上三级领导批示:年 月 日上二级领导批示:年 月 日会签:年 月 日 XZ-BG/BD02XX公司发文单 密级:签发人:规范审核核稿人:经济审核核稿人:法律审核核稿人:主办单位:拟 稿 人审 稿 人会签:共打印 份,其中文 份;附件 份缓 急:标题: 发文 字 第 号 年 月 日附件:主送:抄报:抄送:抄发:打字: 校对: 缮印: 监印:主题词:XZ-BG/BD07 会议纪要 次会议地点:会议时间: 年 月 日 时 分起 年 月 日 时 分止出席人员: 缺席人员及事由:列席人员:主持人:记录人:议题:序号决 议责任人完成时间主持人意见: 签字: 年 月 日抄报:抄送:XZ-BG/BD04XX公司用印申请单 编号: 年 月 日申请部门申请人用印事由拟用印鉴 公章 合同章 批准人部门经理办公室主任行政总监总经理 注:本单由办公室管理。地形平坦开阔,地层由第四系全新冲积层,第四系上更新统冲层组成,局部表覆第四系全新统人工堆积层。第四系全新统冲积层厚度约2550m,岩性主要为黏土、粉质黏土、粉土、粉砂、细砂;第四系上更新统冲积层厚度大于50m,岩性主要为黏性土、粉土、粉细砂等。管桩深度范围内地层主要为:粉土、黏土、粉质黏土,局部表层为杂填土。coupling Centre shall be checked, the second poured concrete strength of more than 70%. In the process of reaming or boring, apart from the special provisions in factory, does not allow any work that may affect the coupling Centre, such as irrigation, to cylinder connections to flood the condenser pipes and so on. Well boring, hinge bolt hole flange with coupling of vertical, not oblique. Mounting bolts should be added lubricants, typing gently with a small hammer, not too loose or too tight, packed the bolts with the corresponding seal screw hole should be marked. 6.4.5.4.2 coupling reamed and pairings is close to the diameter of bolt bearing good hinge holes, dressed with a good two coupling bolts before you can move the rotor, boring-reaming hole in turn. Coupling bolts must be tight coupling is symmetrical diameter, in boring, reaming, two bolts out. Well boring, hinge bolt hole flange with coupling of vertical, not oblique. Due to the coupling bolts in accordance with hinge holes corresponding to the diameter of the screw holes one by one after processing, processing back bolt installation location cannot be changed, so according to bolt after the actual weight difference of nut and lock washer to match. General requirements for coupling two symmetrical diameter bolt, nut and lock washer's total weight difference should not be greater than 10 g and knocks stamped mark. (See Figure 18) The coupling bolts apply lubricant, and then gently with copper home, not too loose or too tight. Bolt Assembly is finished, symmetrical tightening all bolts to 30%, 50%, 70%, 100% force, and check the coupling flutter and before connecting the circle gradually changes its value should be less than 0.02mm. Tightening torque of the coupling bolts shall comply with the technical requirements manufacturers drawings, with a dynamometric wrench or log tension tools. Three wheel rotor swing test coupling connections should be checked: taking leave,XZ-BG/BD03XX公司发文登记处理簿序号发文日期发文部门发文字号文件标题收文部门及签收记录归档情况 XZ-BG/BD23XX公司对外邮件发文登记薄序号发送日期邮件、文件名称申请邮发部门申请人发往单位经办人备 注XZ-BG/BD05XX公司用印登记表序号日期用印部门申请人事 由用何印批准人用印人备注XZ-BG/BD08XX公司督办单(存根) 编号: 年 月 日承命人姓名承命人所属部门督办主题回复时间承命人签字-XX公司督办单 编号: 年 月 日承命人姓名承命人所属部门督办内容:回复时间督办人签字XZ-BG/BD19XX公司授权书授权时限:自 年 月 日起至 年 月 日止授予职责及权限: