模具术语(中英文对照)

AD-Diameter The tread diameter at the centerline of the tread (EU); also: "T-Diameter"(GT)  AD直径：指胎面中心线直径（EU）。又叫T直径（GT）Auto-lock Ear A Lug on the cone ring used to mount the mold/container in the top half of a 60“ NRM Auto-lock press.  导环上的突缘，用于和60“ NRM Auto-lock 硫化机上半部连接。Bead Ring The tire bead forming ring (also: toe ring)   钢圈，也称 toe ringBead Ring Register The landing and tapered seat that the bead ring fits into  钢圈配合：侧板上，和 钢圈配合的平面及锥面Bottom Container Plate The plate that the bottom sidewall plate is bolted to  模壳底座Bottom Container Plate Lifting Lug A lug attached to the Bottom Container Plate with Horizontal holes used for lifting. 模壳底座吊耳： 装配在底座上、有水平的孔，用来吊装的吊耳Bottom Container Plate Dowel Pin Lug A lug attached to the Bottom Container Plate that supports the Dowel Pin Bushing.  装配在底座上，用来支承定位销套的突缘Bottom Container Plate Hold Down A lug that is used to fix the Bottom Plate in the Press.  用来将底座装配在硫化机上的突缘Breaker Hook A hook fixed to the bottom of the tread segment that catches the bottom container plate only when the segment will not release from the tire during de-molding.分离钩：固定在花纹块底部的钩子，轮胎硫化完后若花纹块不能跟轮胎分离，就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。Breaker Hook Guide PieceA block bolted to the breaker hook that aligns the tread segment with a slot in the bottom container plate.   分离钩导块：用螺栓固定在Breaker Hook上，定位花纹块和模壳底座上槽的定位块。Bronze Wear Plates Any sacrificial metal plate placed under, over or behind a component to keep the components from wearing on each other (greasing)  青铜耐磨板(油润滑的)Casting An un-machined cast metal tread ring or Segment  铸件：未加工的金属花纹圈或花纹块铸件。Centering Ring The ring mounted on the bottom press platen to locate the mold/ container concentrically to the press; also: "Press register"  定中环,也称“Press register”Clamp Rings The bladder clamping assembly   胶囊夹盘Cone Ring The outer ring that transforms the axial movement of the press in a radial one of the segments; also: "Actuator ring", "Squeeze ring" (GT)  导环，也称"Actuator ring", "Squeeze ring"Conicity Difference between tread radius over the width   锥度Container The mechanical parts that allow a segmented mold to operate; also: mechanism (GT)  模壳,也叫 mechanismContainer Cavity The space inside of the container that the mold fits into  模壳腔：模壳部放置模具的空间。DD-Diameter Nominal diameter of a bead ring (EU) Also: "Heel diameter" (GT)  钢圈的公称直径, 也叫"Heel diameter"Decoupler Rib A narrow rib that runs circumferentially around the mold and is located near the shoulder area  在胎肩部位、窄的的圆周向的花筋DEVA Metal Graphite impregnated bronze metal used for wear plates in segmented molds (un-greased)  DEVA类耐磨板：石墨青铜金属，用来制作活络模具的耐磨板（自润滑）。Dowel Pins The pins that keep the mold halves and parts aligned (containers or HKK molds)  定位销：用来对模具的半模或零件定位的销（模壳或HKK模具）。Dowel Pin Bushing A replaceable sleeve used to register the Dowel Pin locations.定位销套：对定位销进行定位的可更换的衬套。DS 2-Diameter The junction diameter between the sidewall plate and the tread segments or tread ring and mould back cavity (EU); also: "S Diameter"(GT)  口径：侧板与花纹块、花纹圈与mould back 的配合直径. 也叫"S Diameter"End Gap The distance between cold mold segments (20°C) that allows for heat expansion 竖缝间隙： 20°C时花纹块竖缝允许热膨胀的间隙Exterior Mold Identification Plate A removable plate fastened to the outside of the cone ring listing information pertaining to the mold parts (tread segments, side-plates) assembled in the container.  模壳铭牌Filler rings Full sidewall inserts for molds that fills from the off shoulder area to the I.D.  嵌入式侧板:从肩部到径，全部嵌入模具的侧板Front of mould The reference point at which all dimensional locations are referred  模具正前方Heel Diameter See: DD-Diameter  见 DD-DiameterGuide Piece A block fixed to the Top Container Plate that registers to a slot in the Cone Ring to keep the Top plate from turning during operation.  导向块：固定在上盖上，和导环上的槽定位，防止操作过程中上盖转动Insert Metal plates pushed or screwed in the side wall plate for exchangeable information活字块(牌)Insulation Jacket Insulation placed around a container or 2 piece mold (GT) to retain heat  保温套Integral type mechanism A mold (tread area) and mechanism that are one unit  整体式模壳: 花纹部分和模壳是一体的Ledge Height Bead ledge width on a bead ring   钢圈上凸出部位的宽度Lettering The inside lettering of the sidewall; also: "Sidewall engraving" (GT)  侧板字体图. 也叫"Sidewall engraving" Maxi Vent (GT) Vent Sleeve A removable insert for vent holes (Dia.:1,33 mm) to be trimmed. 大气孔套(直径.:1,33 mm)Mechanism (GT) See: container or semi-container  见container 或semi-containerMicro Vent A removable insert with vent slots (< 0.1 mm)   微型气孔套：（< 0.1 mm）Mini Vent (MV) A removable insert for vent holes (Dia.: 0,6 mm)    迷你气孔套(直径.:0.6 mm)Mold Back The part of a two piece mold machined to hold the tread ring and filler rings  除花纹圈和嵌入侧板外的两半模外壳Mold Cavity The inside of the mold that the tyre is shaped in   模具腔：形成轮胎外型的模具部曲线Mold Register The taper at the O.D. of a 2 piece mould that aligns the mold concentrically   两半模具上下半模的定位锥面P