463编号焊接工艺规程WPS模版
焊 接 工 艺 规 程 (WPS)焊 接 工 艺 规 程 (WPS) WELDING PROCEDURE SPECIFICATION WPS No.: WPS-H005 WPS-H005 PAGE 1 1 OF 3 3 DATE 2003.03.10 2003.03.10 公司名称 Company Name 依据的 PQR 编号 Supporting PQR No. PQR-07 PQR-07 签字人 BY(QA DIRECTOR) 生效日期 Date 焊接方法 Welding Process MAG MAG 自动化等级 Type(s)Semi-Auto (Automatic,Manual,Machine,Semi-Auto.) 接头 JOINTS 接头 JOINTS 接头型式 Joint Design Vee Vee “V型接头V型接头 衬垫 Backing(有/Yes) (无/NO) 垫块 Retainers(有/Yes) (无/NO) (Refer to both backing and retainers.) 衬垫材料(型号) Backing Material(Type) Base metal Base metal 金属 Metal; 不熔化金属 Non-fusing Metal; 非金属 Non-metallic; 其它 Other Sketches,production drawings,weld symbols or written description should show the general arrangement of The parts to be welded. Where applicable,the root spacing and the details of weld groove may be specified. 母材 BASE METALS 母材 BASE METALS 类别号 PNo. 组号 Group No. 1 1 与类别号 to PNo. 组号 Group No. 1 1 相焊, 或 or 钢号/等级为 Specification Type and Grade St52-3St52-3 与钢号/等级为 to Specification Type and Grade St52-3St52-3 相焊, 或 or 化学成分/力学性能为 Chem.Analysis and Mech. Prop. 与化学成分和力学性能为 to Chem.Analysis and Mech. Prop. 相焊 厚度范围 Thickness Range: 母材 Base Metal: 坡口焊 Groove 324mm 324mm 角 焊 Fillet not limited not limited 管径范围 Pipe Dia. Range: 坡口焊 Groove Not Limitted Not Limitted 角 焊 Fillet not limited not limited 其它 Other 填充金属 FILLER METALS 填充金属 FILLER METALS SFA No. SpecialSpecial AWS No.(Class) ANSI/AWS A5.18 ER70S-6 上海中钢焊材有限公司ANSI/AWS A5.18 ER70S-6 上海中钢焊材有限公司 FNo. NoneNone A-No. NANA 填充金属尺寸 Size of Filler Metals 1.2mm1.2mm 焊 接 工 艺 规 程 (WPS)焊 接 工 艺 规 程 (WPS) WELDING PROCEDURE SPECIFICATION WPS No.: WPS-H005 WPS-H005 PAGE 2 2 OF 3 3 DATE 2003.03.102003.03.10 熔敷焊缝金属厚度范围 对接焊缝 Deposited Weld Met.Thickness Range: Groove max 24mmmax 24mm 角焊缝 Fillet not limitednot limited 焊丝一焊剂 Electrode-Flux (Class) NANA 焊剂商标 Flux Trade Name NANA 熔化性嵌条 Consumable insert NANA 其 他 Other 焊接位置 POSITIONS 焊接位置 POSITIONS 焊接位置 sition (s) of groove PAPA 焊接方向 Weld.Progression: 向上 UP X X 向下 Down NO NO 角焊缝位置 Position(s) of Fillet PA PA 预热 PREHEAT 预热 PREHEAT 最小预热温度 Preheat Temp. Min. 5 5 最大层间温度 Inter pass Temp. Max. 300 300 预热保持方式 Preheat Maintenance None None (Continuous or special heating where applicable shall be recorded) 焊后热处理 POST-WELD HEAT TREATMENT 焊后热处理 POST-WELD HEAT TREATMENT 温度范围 Temperature Range 时间范围 Time Range 气体 GAS 气体 GAS 百分组成 Percent Composition 气体 Gas(es) 混合剂(Mixture) 流量 Flow Rate 保护气 Shielding 二氧化碳+ 氩气 18/82 15-25L/min 二氧化碳+ 氩气 18/82 15-25L/min 尾部保护气 Trailing None None None None None 背面保护气 Backing None None None None None None 电特性 ELECTRICAL CHARACTERISTICS 电特性 ELECTRICAL CHARACTERISTICS 交流或直流 Current AC or DC DC DC 极性 Polarity EP EP 电流(范围) Amps(Range) see below see below 电压(范围) Volts(Range) see belowe see belowe 钨极尺寸和类型(纯钨极或 2%钍钨极等) Tungsten Electrode Size and Type(Pure.Tungsten.2% thoriated.etc.) NA NA 金属过渡方式(射流或短路等) Mode of Metal Transfer for GMAW (Spray arc, short circuiting arc, etc.) NA NA 送丝速度范围 Electrode Wire Feed Speed Range NA NA 施焊技术 TECHNIQUE 施焊技术 TECHNIQUE 无摆动焊或有摆动焊 String or Weave Bead String 无摆动焊 String 无摆动焊 喷孔或喷嘴尺寸 Orifice or Gas Cup Size NA NA 焊 接 工 艺 规 程 (WPS)焊 接 工 艺 规 程 (WPS) WELDING PROCEDURE SPECIFICATION WPS No.: WPS-H005 WPS-H005 PAGE 3 3 OF 3 3 DATE 2003.03.102003.03.10 打底及中间焊道的清理方法(刷理或打磨等) Initial and Inter pass Cleaning(Brushing.Grinding.etc.) Grinding 磨 Grinding 磨 背部清根方法 Method of Back Gouging Carbon arc gouging 、 Grinding 碳弧气刨、磨 Carbon arc gouging 、 Grinding 碳弧气刨、磨 摆动方法 Oscillation NA NA 导电咀-工件距离 Contact Tube To Work Distance NA NA 多道焊或单道焊(每侧) Multiple or Single Pass (per side) Multiple 多道焊 Multiple 多道焊 多丝焊或单丝焊 Multiple or Single Electrodes NA NA 焊