Text Display (TD) User Manual

Preface Contents Product Overview1 Installing Your TD Device2 Using the Keypad Designer to Create a Custom Faceplate for Your TD 200C 3 Using the TD 200 Wizard to Configure the S7 200 CPU for Your TD Device 4 Operating Your TD Device5 Appendices Technical Specifications and Reference Information A Connecting Multiple Devices on a Network B TroubleshootingC Index Text Display TD User Manual SIMATIC Edition 06 2004 www PLC ii Safety Guidelines This manual contains notices which you should observe to ensure your own personal safety as well as to protect the product and connected equipment These notices are highlighted in the manual by a warning triangle and are marked as follows according to the level of danger Danger Danger indicates an imminently hazardous situation which if not avoided will result in death or serious injury Warning Warning indicates a potentially hazardous situation which if not avoided could result in death or serious injury Caution Caution used with the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury Caution Caution used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage Notice Notice indicates a potential situation which if not avoided may result in an undesirable result or state Qualified Personnel Only qualified personnel should be allowed to install and work on this equipment Qualified per sons are defined as persons who are authorized to commission to ground and to tag circuits equipment and systems in accordance with established safety practices and standards Correct Usage Note the following Warning This device and its components may only be used for the applications described in the catalog or the technical descriptions and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens This product can only function correctly and safely if it is transported stored set up and installed correctly and operated and maintained as recommended Trademarks SIMATICR SIMATIC HMIR and SIMATIC NETR are registered trademarks of SIEMENS AG Some of other designations used in these documents are also registered trademarks the owner s rights may be violated if they are used by third parties for their own purposes We have checked the contentsof thismanual for agreement with the hardware and software described Since deviationscannot be precluded entirely we cannot gua rantee full agreement However the datain thismanual arereviewed regularlyand any necessary correctionsincluded in subsequent editions Suggestionsfor impro vement are welcomed Disclaimer of LiabilityCopyright Siemens AG 2004 All rights reserved The reproduction transmission or use of this document or its contents is not permitted without express written authority Offenders will be liable for damages All rights including rightscreated by patent grant or registration of a utilitymodel or design are reserved Siemens AG Bereich Automation and Drives Geschaeftsgebiet Industrial Automation Systems Postfach 4848 D 90327 Nuernberg E Siemens AG 2004 Technical data subject to change Siemens Aktiengesellschaft www PLC iii Preface Purpose of the manual The SIMATIC Text Display TD User Manual is a combination user and reference manual that describes the operation of the TD devices TD 200 and TD 200C with an S7 200 CPU Required Basic Knowledge This manual is designed for engineers programmers and maintenance personnel who have a general knowledge of programmable logic controllers and operator interfaces Scope of This Manual This manual describes the installation configuration and operation of both the TD 200 version 3 0 and the TD 200C version 1 0 This manual also describes the TD 200 wizard of STEP 7 Micro WIN used to configure the S7 200 CPU for either TD device and the Keypad Designer application used to configure the keypad of the TD 200C To utilize the new features of these TD devices you must use STEP 7 Micro WIN version 4 0 or greater Agency Approvals These SIMATIC TD devices meet the standards and regulations of the following agencies Underwriters Laboratories Inc UL UL 60950 Canadian Standards Association CSA C22 2 No 60950 standard Refer to Appendix A for additional compliance information Certification These SIMATIC TD devices have the following certification Underwriters Laboratories UL Standards UL 60950 and CSA C22 2 No 60950 Factory Mutual Research Standard Class Number 3611 Class I Division 2 Group A B C D and Class I Zone 2 Group IIC Temperature class T5 is adhered to when the ambient temperature during operation does not exceed 60 C CE Labeling These SIMATIC TD devices fulfill the requirements and protection guidelines of the following EU directives EC Directive 73 23 EEC Low voltage directive EC Directive 89 336 EEC EMC directive C Tick These TD devices are compliant with requirements of the AS NZS 3548 Australian standard Recy