WinCC flexible 2005 Migration_en

SIMATIC HMI WinCC flexible 2007 WinCC flexible 2007 Migration SIMATIC HMI WinCC flexible 2007 WinCC flexible 2007 Migration Preface Preface Basics Basics 1 1 Migration without changingMigration without changing the HMI the HMI 2 2 Migration with change Migration with change of the HMI of the HMI 3 3 Migration from OP3 to OP 73Migration from OP3 to OP 73 4 4 Migration of OP7 to OP 77 Migration of OP7 to OP 77 5 5 Migration from OP17 toMigration from OP17 to OP 177B OP 177B 6 6 Migrating a ProTool projectMigrating a ProTool project with P350 PLC with P350 PLC 7 7 SIMATIC HMISIMATIC HMI WinCC flexible 2007WinCC flexible 2007 Migration Migration User s Manual User s Manual 07 2007 07 2007 A5E01056435 01 This user manual is part of the documentation package with the order number 6AV6691 1AB01 2AB0 www PLC Safety Guidelines Safety Guidelines Safety Guidelines Safety Guidelines This manual contains notices you have to observe in order to ensure your personal safety as well as to prevent damage to property The notices referring to your personal safety are highlighted in the manual by a safety alert symbol notices referring only to property damage have no safety alert symbol These notices shown below are graded according to the degree of danger DANGER DANGER indicates that death or severe personal injury willwill result if proper precautions are not taken WARNING WARNING indicates that death or severe personal injury maymay result if proper precautions are not taken CAUTION CAUTION with a safety alert symbol indicates that minor personal injury can result if proper precautions are not taken CAUTION CAUTION without a safety alert symbol indicates that property damage can result if proper precautions are not taken NOTICE NOTICE indicates that an unintended result or situation can occur if the corresponding information is not taken into account If more than one degree of danger is present the warning notice representing the highest degree of danger will be used A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage Qualified Personnel Qualified Personnel The device system may only be set up and used in conjunction with this documentation Commissioning and operation of a device system may only be performed by qualified personnelqualified personnel Within the context of the safety notes in this documentation qualified persons are defined as persons who are authorized to commission ground and label devices systems and circuits in accordance with established safety practices and standards Prescribed Usage Prescribed Usage Note the following WARNING WARNING This device may only be used for the applications described in the catalog or the technical description and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens Correct reliable operation of the product requires proper transport storage positioning and assembly as well as careful operation and maintenance Trademarks Trademarks All names identified by are registered trademarks of the Siemens AG The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner Disclaimer of Liability Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described Since variance cannot be precluded entirely we cannot guarantee full consistency However the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions Siemens AG Automation and Drives Postfach 48 48 90437 N RNBERG GERMANY Order number 6AV6691 1AB01 2AB0 07 2007 Copyright Siemens AG 2007 Technical data subject to change www PLC WinCC flexible 2007 Migration User Manual 07 2007 6AV6691 1AB01 2AB0 3 Preface Preface Purpose of this manual Purpose of this manual This user manual is part of the WinCC flexible documentation Projects created with ProTool or WinCC can be re used with WinCC flexible This manual contains the following information Basic principles of migration HMI device for which the migration is performed without replacement of an HMI device HMI device for which the migration is performed with replacement of an HMI device Migration from OP3 to OP 73 or OP 73 micro Migration from OP7 to OP 77B or OP 77A Migration from OP 17 to OP 177B Replacement of ProTool objects with WinCC flexible objects This manual is intended for project engineers commissioning engineers and service technicians who are involved in migration to WinCC flexible The help integrated in WinCC flexible the WinCC flexible Information System contains detailed information The information system contains instructions examples and reference information in electronic form Basic Knowledge Requirements Basic Knowledge Requirements General knowledge in the field of automation engineering is required to understand this m