S7-400 Hardware and Installation_en

Preface Contents Product Overview 1 Installing the S7 400 2 Addressing the S7 400 3 Wiring the S7 400 4 Networking 5 Commissioning 6 Maintenance 7 Appendices Assembling and Installing Systems A Guidelines for Handling Electro statically Sensitive Devices ESD B Glossary Index 11 2006 A5E00850741 01 Automation System S7 400 Hardware and Installation Installation Manual SIMATIC This manual is part of the documentation package with the order number 6ES7498 8AA05 8BA0 www PLC Danger indicates that death or severe personal injury will result if proper precautions are not taken Warning indicates that death or severe personal injury may result if proper precautions are not taken Caution with a safety alert symbol indicates that minor personal injury can result if proper precautions are not taken Caution without a safety alert symbol indicates that property damage can result if proper precautions are not taken Notice indicates that an unintended result or situation can occur if the corresponding notice is not taken into account If more than one degree of danger is present the warning notice representing the highest degree of danger will be used A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage Qualified Personnel The device system may only be set up and used in conjunction with this documentation Commissioning and operation of a device system may only be performed by qualified personnel Within the context of the safety notices in this documentation qualified persons are defined as persons who are authorized to commission ground and label devices systems and circuits in accordance with established safety practices and standards Prescribed Usage Note the following Warning This device and its components may only be used for the applications described in the catalog or the technical description and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens Correct reliable operation of the product requires proper transport storage positioning and assembly as well as careful operation and maintenance Trademarks All names identified by are registered trademarks of the Siemens AG The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner Disclaim of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described Since variance cannot be precluded entirely we cannot guarantee full consistency However the information in this publication is reviewed regularly and any necessary corrections are included in sub sequent editions Safety Guidelines This manual contains notices you have to observe in order to ensure your personal safety as well as to prevent damage to property The notices referring to your personal safety are highlighted in the manual by a safety alert symbol notices referring to property damage only have no safety alert symbol The notices shown below are graded according to the degree of danger Copyright Siemens AG 2006 Technical data subject to change SIEMENS AG Automation and Drives Postfach 4848 90437 N RNBERG GERMANY A5E00850741 01 11 2006 www PLC iii Automation System S7 400 Hardware and Installation A5E00850741 01 Preface Purpose of the Manual The manual contains reference information on operator actions descriptions of functions and technical specifications of the central processing units power supply modules and interface modules of the S7 400 How to configure assemble and wire these modules and other in an S7 400 system is described in the installation manuals for each system Required Basic Knowledge You will need general knowledge of automation to understand this manual Prerequisite is also sufficient knowledge in the use of computers or PC type equipment programming devices for example with Windows 2000 or XP operating system The S7 400 system is configured in STEP 7 standard software You should therefore have sufficient knowledge of this standard software This knowledge is provided in the Programming with STEP 7 manual Please note the information on the safety of electronic control systems in the appendix of this manual in particular when operating an S7 400 in safety relevant areas Scope of this Manual The manual applies to the S7 400 automation system Approvals You can find details on approvals and standards in the Module Data reference manual Place of this Documentation in the Information Environment This manual is part of the documentation package for S7 400 SystemDocumentation Package S7 400 S7 400 Programmable Controller Hardware and Installation S7 400 Programmable Controllers Module Data Automation System S7 400 CPU Data S7 400 Instruction List www PLC Preface iv Automation System S7 400 Hardware and Installation A5E00850741 01 Navigating The manual offers the following access help to make it easy for you to find spe